construction dryer

sold out until spring 2025 A powerful dehumidifier with a semi-professional design. The metal casing and the internal components are solid and durable. The X40 is particularly efficient in a classic basement environment, but also economical in consumption. service The target humidity can be set using the clear control panel on the top of the device. Once the target humidity is reached, the dehumidification operation pauses while only the ventilation continues to determine the current humidity. Various setting options are available:  continuous operation The device runs continuously and ignores the measured room humidity. This setting is useful if you want to dry laundry or when drying water damage.  Operation with selected target humidity 30 – 90% Any target humidity value between 30% and 90% can be selected at the touch of a button (5% increments). To prevent mold and odors, it is sufficient to maintain a humidity of around 60%. The ideal setting is therefore 55 or 60%. For economical operation, the software has a tolerance of 6% so that the compressor does not start at too short intervals. The set target humidity value corresponds to the average value +-3%. This means that the drying process runs until the set value is undershot by 3%. The operation then pauses until the set value is overshot by 3%. So if you select 55%, for example, the room humidity fluctuates between min. 52% - max. 58%. comfort mode The "Dryfix Intelligence" control automatically optimizes operation taking the room temperature into account: - If the ambient temperature is below 5° C, the compressor stops to prevent the unit from icing up. - When the ambient temperature is higher than 5°C and lower than 20°C, the device operates with a target humidity of 60%. - When the ambient temperature is higher than 20°C and lower than 27°C, the device operates with a target humidity of 55%. - If the ambient temperature is higher than 27° C, the device operates with a target humidity of 50%. large tank The condensate tank, which is inserted at the back, holds 6.5 liters and stops operation when it is full using the integrated float magnetically. The fill level is immediately visible on the front of the device: blue light = operation in progress, red light = tank full or not inserted correctly (operation is interrupted). The hose connection is located directly above the tank, through which the condensate can also be drained directly into a drain (suitable hose: 10 mm inner diameter).  Two ventilation levels The air flow is powerful. The slats at the top of the device can also be used to direct the dry air in a certain direction. This is very useful if, for example, you want to blow into a laundry hanger or onto a damp wall. Due to the powerful ventilation, the operating noise is easily audible (a noise comparable to that of a steam extractor). At the touch of a button, you can choose between weak (quieter) or strong ventilation. With this model, the compressor (= dehumidification) stops when the desired humidity is reached, while the fan runs continuously to circulate the room air. Features & advantages over other dehumidifiers: • Digital control panel for regulating the desired humidity • Automatic function, ie the dehumidification mode switches off automatically when the target humidity level is reached and also switches on again automatically when it becomes more humid (including a +/- 6% power saving function so that the device does not switch on and off unnecessarily often. • Automatic professional defrost function • Suitable for unattended use • Also suitable for continuous operation/continuous dehumidification • Optimized for use in classic basement environments • Power consumption of only 470W at 20°C/60% humidity (starting current max. 700W) • Equipped with a very reliable quality brand compressor • Comfort program with protection at unsuitably cold room temperatures • No adjustments in case of power failure (device continues where it was interrupted) • Auto-stop when condensate tank is full including warning light • Removable 6.5 liter condensate tank • Possibility of connecting a hose for continuous drainage of the condensate. • Absolutely maintenance-free / No separate or renewed coolant is required (closed circuit) • Very easy mobility thanks to side handles and castors • Washable air filter • Modern design and attractive appearance • The device is ready for use immediately (no installation or assembly required) • CFC free • CE, GS and RoHS tested • Latest, environmentally friendly refrigerant R290 (GWP: 3) usage examples Cellar damp : Ideal for damp cellars, old walls and laundry rooms. Eliminates musty smells, stops mold growth, decomposition of masonry and much more. Mobile clothes dryer : the device is also very popular as a mobile clothes dryer. Close the laundry room windows and doors and, depending on the size of the laundry room, the laundry will dry overnight. dehumidification performance The dryer can be used over a wide temperature range between +5°C and +35°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: 30°C / 80% humid: 40 liters (90%: 44 liters, 60%: 22 liters) 20°C / 80% humid: 22 liters (90%: 28 liters, 60%: 14 liters) 15°C / 80% humid: 18 liters (90%: 22 liters, 60%: 10 liters) 10°C / 80% humid: 12 liters (90%: 16 liters, 60%: 8 liters) 5°C / 80% humid: 9 liters (90%: 11 liters, 60%: 5 liters) HEPA filter option In addition to the standard filter, which filters the dust out of the air, a HEPA filter can be ordered for the X40. This HEPA filter cleans the air every time the device passes through with a purity rate of almost 100%. This means that even the finest particles such as pollen, fine dust, mold spores and other tiny contaminants are intercepted. Also viruses of all kinds (including corona). The filter is therefore highly recommended, for example in basements with mold infestation, but also when drying laundry so that flying pollen is not blown through the hanging laundry and contaminates it (e.g. in the case of pollen allergy). The HEPA filter is a consumable and cannot be washed. The price of CHF 38 includes the filter with holder. For repeat orders, the filter alone without holder can be reordered at a reduced price of CHF 29. scope of delivery Plug-in ready device, no assembly required. The optional HEPA filter is not included in the basic package.  Technical data   Tension 220V-240V / 50Hz power consumption max. 700W max. / 470W (at 20°C/60% RH) sound pressure level (our measurement) 1 m distance 56 dB(A), 2.5 m distance 54 dB(A) dehumidification performance max. 40 liters/day (30°C / 80% RH) drying clothes about 3-4 washing machine loads per day condensate tank Approx. 6.5 liters refrigerant: R290 / 148 gr. Dimensions (H x W x D) 540 x 400 x 310 mm Weight 23 kg cessation of operations Digital ambient temperature Manufacturer's specification 5°C ~ 35°C (our recommendation: from 7°C) Swiss plug Yes hose connection Yes / suitable hose 10mm inner diameter guarantee 2 years

Read more less

The "105S" dehumidifier closes the gap between inexpensive household dehumidifiers and professional construction dryers. This device is a Trotec in-house development that has taken many customer needs into account. It is made in Germany and is very attractive in terms of what you pay for and what you get. The "105SHC" version offered here is the extended version with a built-in hour counter for optimal control of operation and consumption.     Robust but lightweight   The housing is made of robust aluminum. Aluminum has the advantage that it is durable, but still remains light in weight at just 14.5 kg, which makes carrying the device easier. The dryer also stands on four feet.     Easy operation   The simple control panel allows you to read the current room humidity and temperature, and the desired target humidity can be selected at the touch of a button. The integrated hygrostat stores the value and regulates the performance of the compressor and two-stage fan automatically and in line with requirements. Thanks to the advanced software, the dryer works precisely and more economically than other devices with comparable dehumidification power. Continuous operation is also possible on request.   Timer function: If you want to limit the operation to a specific time, you can use the integrated timer. If you want the dryer to work at the same times every day, it can also be connected to an external timer. Thanks to the memory function, the dehumidifier remembers the last setting and resumes operation with the same setting after a power failure (for example, if you only want to dehumidify during low tariff periods).     Bucket with float and direct hose connection   The condensate water extracted from the air is collected in the inserted bucket as standard. This has a comfortable capacity of 5.2 liters. A float automatically stops operation when the bucket is full. Alternatively, a hose can be connected to drain the water directly into a lower drain. The hose must be laid in a downward direction as there is no pump integrated into the device.     Easy-to-clean air filter   To prevent the interior of the device from becoming excessively dirty, a filter cleans the air in the intake area. This filter is easy to remove and clean. It is reusable.     Advantages at a glance • Hygrostat control with real-value humidity preselection • Digital display of the current humidity and temperature values • Electronic automatic defrosting • 2 fan speeds • Level warning light when water tank is full • Optional fully automatic or continuous operation • Overflow protection with automatic shutdown • Washable air filter • Timer function • Carrying handles • Connection for external condensate drain • Stackable aluminum housing - light and robust • Professional quality “made in Germany” with a good price-performance ratio     Technical data   dehumidification performance at 30 °C / 80 % RH 28.4 liters / day air volume 173 m³/h Maximum room size 70 m² (175 m³) Minimum room size 4 m² (15 m³) temperature range 5 - 32°C Selectable target humidity Achievable target humidity 30 - 90 % RH 35 - 90% RH (finned evaporator) voltage 220 - 240 V/50 Hz nominal current consumption max. 2.1 A power consumption max. 500W Recommended coverage 10 A cable length approx. 1.5 m Plug EU plug with Swiss adapter refrigerant R290 (125g) GWP3 water bucket 5.2 liters operating noise 50 dB(A) at 1 m distance 47 dB(A) at 2.5 m distance Dimensions D x W x H 250 x 342 x 517 mm Weight 14.5 kg defrosting automatic recirculation, electronic automatic dehumidification hygrostat-controlled fan radial, 2-stage fan automatic shutdown when bucket is full Yes prefilter Yes timer Yes continuous operation possible Yes operating hour meter Yes display shows current room humidity, set humidity memory function yes (saves set values ​​automatically) hose connection yes, short hose piece included guarantee 2 years    

Read more less

A good, affordable racehorse for construction dryers and water damage repairers. Everything that is unnecessary for continuous use has been consistently left out of this dehumidifier. It has neither a display nor a hygrostat (a plug-in hygrostat can be ordered as an option if required). This makes it very easy to use, safe from tampering and extremely affordable. On the other hand, everything that is needed for effective and fast drying is there: powerful dehumidification performance, hot gas defrosting, hour counter as well as large rollers and a guide bar for easy mobility on construction and damage sites.     Easy operation   Commissioning is child's play. Plug in, flip the main switch, and you're done!   The operation will now continue until either the bucket is full or until the dryer is uninstalled. As long as the device is connected to the power supply, it will run reliably and there are no settings that can be accidentally changed or manipulated. This also applies in the event of a power failure: if the power comes back on, the dehumidifier will continue its task with the same settings.   Thanks to the professional hot gas automation, it can also be used in cooler environments without any problems, although the dehumidification power decreases at cold temperatures, as with all condensation dryers. The built-in finned evaporator (cooling element) has an extremely high efficiency in temperate environments and can dry the air to just under 40% RH. The dryer is also equipped with a rotary piston compressor. This means that it can be transported and stored in any position.     Optional hygrostat   Should a hygrostat be required at some point to regulate the target humidity, the dryer is prepared so that the Trotec hygrostat HG110 can be connected directly using a jack plug. Please note the accessories.     bucket and direct hose connection   The water extracted from the air is collected in a 5-litre bucket. A magnetic float automatically stops operation when the bucket is full and a warning light indicates visually that the bucket should be emptied. If necessary, a hose can be connected to the bucket itself if the water can be drained away directly. The hose must be laid in a downward direction as there is no pump integrated into the dryer.     Suitable for unattended continuous operation   This "TTK" is suitable for longer, unattended drying operations. The exact operating time can be determined precisely using the hour counter that is integrated as standard. This is particularly useful for commercial applications. Thanks to the counter, it is also possible to determine whether the device was always in operation or whether it was switched off accidentally or intentionally.     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection.   The natural refrigerant propane (R290) is an organic compound and is classified as a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Additional benefit for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.     Advantages at a glance   • Affordable price with strong performance in the commercial sector • Can also be used in cooler environments thanks to hot gas defrosting • Robust steel construction with large rollers and guide bar • Suitable for continuous operation • Can be transported and stored in any position thanks to the rotary piston compressor • External hygrostat connection     Technical data   dehumidification performance at 30 °C / 80 % RH 50 liters / day air volume 350 m³/h Maximum room size 125 m² (310 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C humidity range technically humidity range practice 35 - 90 % RH 40 - 90% RH (finned evaporator) voltage 220 - 240 V/50 Hz nominal current consumption max. 3.7 A power consumption max. 820W Recommended coverage 10 A cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (230g) GWP3 water bucket 5 liters operating noise 56 dB(A) at 1 m distance 53 dB(A) at 2.5 m distance Dimensions D x W x H 495 x 455 x 900 mm Weight 31 kg defrosting automatic hot gas automatic dehumidification Continuous operation, a plug-in mechanical hygrostat is available as an option. fan axial, 1-stage fan automatic shutdown when bucket is full Yes prefilter Yes operating hour meter Yes continuous operation possible Yes display no memory function yes (saves set values ​​automatically) hose connection yes, not included in delivery (suitable inner diameter: 12 mm) guarantee 2 years

Read more less

The Quadro X80 is a very powerful dehumidifier with a semi-professional design. The metal casing and the internal components are solid and durable. The X80 is particularly efficient in a classic basement environment, but also economical in consumption. service The target humidity can be set using the clear control panel on the top of the device. Once the target humidity is reached, the dehumidification operation pauses while only the ventilation continues to determine the current humidity. Various setting options are available:  continuous operation The device runs continuously and ignores the measured room humidity. This setting is useful if you want to dry laundry or when drying water damage.  Operation with selected target humidity 30 – 90% Any target humidity value between 30% and 90% can be selected at the touch of a button (5% increments). To prevent mold and odors, it is sufficient to maintain a humidity of around 60%. The ideal setting is therefore 55 or 60%. For economical operation, the software has a tolerance of 6% so that the compressor does not start at too short intervals. The set target humidity value corresponds to the average value +-3%. This means that the drying process runs until the set value is undershot by 3%. The operation then pauses until the set value is overshot by 3%. So if you select 55%, for example, the room humidity fluctuates between min. 52% - max. 58%. comfort mode The "Dryfix Intelligence" control automatically optimizes operation taking the room temperature into account: - If the ambient temperature is below 5° C, the compressor stops to prevent the unit from icing up. - When the ambient temperature is higher than 5°C and lower than 20°C, the device operates with a target humidity of 60%. - When the ambient temperature is higher than 20°C and lower than 27°C, the device operates with a target humidity of 55%. - If the ambient temperature is higher than 27° C, the device operates with a target humidity of 50%. large tank The condensate tank, which is inserted at the back, holds 6.5 liters and stops operation when it is full using the integrated float magnetically. The fill level is immediately visible on the front of the device: blue light = operation in progress, red light = tank full or not inserted correctly (operation is interrupted). The hose connection is located directly above the tank, through which the condensate can also be drained directly into a drain (suitable hose: 10 mm inner diameter).  Two ventilation levels The air flow is powerful. The slats at the top of the device can also be used to direct the dry air in a certain direction. This is very useful if, for example, you want to blow into a laundry line or onto a damp wall. Due to the powerful ventilation, the operating noise is easily audible (a noise comparable to that of a steam extractor). At the touch of a button, you can choose between weak (quieter) or strong ventilation. With this model, the compressor (= dehumidification) stops when the desired humidity is reached, while the fan runs continuously to circulate the room air. Features & advantages over other dehumidifiers: • Digital control panel for regulating the desired humidity • Automatic function, ie the dehumidification mode switches off automatically when the target humidity level is reached and also switches on again automatically when it becomes more humid (including a +/- 6% power saving function so that the device does not switch on and off unnecessarily often. • Automatic professional defrost function • Suitable for unattended use • Also suitable for continuous operation/continuous dehumidification • Optimized for use in classic basement environments • Low power consumption compared to the powerful performance • Equipped with a very reliable quality brand compressor • Comfort program with protection at unsuitably cold room temperatures • No adjustments in the event of a power failure (device continues where it was interrupted) • Auto-stop when condensate tank is full including warning light • Removable 6.5 liter condensate tank • Possibility of connecting a hose for continuous drainage of the condensate. • Absolutely maintenance-free / No separate or renewed coolant is required (closed circuit) • Very easy mobility thanks to side handles and castors • Washable air filter • Modern design and attractive appearance • The device is ready for use immediately (no installation or assembly required) • CFC free • CE, GS and RoHS tested • Latest, environmentally friendly refrigerant R290 (GWP: 3) usage examples Cellar damp : Ideal for damp cellars, old walls and laundry rooms. Eliminates musty smells, stops mold growth, decomposition of masonry and much more. Mobile clothes dryer : the device is also very popular as a mobile clothes dryer. Close the laundry room windows and doors and, depending on the size of the laundry room, the laundry will dry overnight. dehumidification performance The dryer can be used over a wide temperature range between +7°C and +35°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: 30°C / 80% humid: 80 liters (90%: 88 liters, 60%: 44 liters) 20°C / 80% humid: 44 liters (90%: 56 liters, 60%: 28 liters) 15°C / 80% humid: 36 liters (90%: 44 liters, 60%: 20 liters) 10°C / 80% humid: 24 liters (90%: 32 liters, 60%: 16 liters) 5°C / 80% humid: 18 liters (90%: 22 liters, 60%: 10 liters) HEPA filter option In addition to the standard filter, which filters dust out of the air, a HEPA filter can be ordered for the X80. This HEPA filter cleans the air every time it passes through the device with a purity rate of almost 100%. This means that even the finest particles such as pollen, fine dust, mold spores and other tiny contaminants are intercepted. Also viruses of all kinds (including corona). The filter is therefore highly recommended, for example in basements with mold infestation, but also when drying laundry so that flying pollen is not blown through the hanging laundry and contaminates it (e.g. in the case of pollen allergy). The HEPA filter is a consumable and cannot be washed. The price of CHF 38 includes the filter with holder. For repeat orders, the filter alone without holder can be reordered at a reduced price of CHF 29. scope of delivery Plug-in ready device, no assembly required. The optional HEPA filter is not included in the basic package.  Technical data  Tension 220V-240V / 50Hz power consumption max. 1291W max. / 940W (at 20°C/60% RH) sound pressure level 1 m distance 56 dB(A) (our measurement) 2.5 m distance 54 dB(A) (our measurement) dehumidification performance 80 liters/day (30°C / 80% RH) condensate tank Approx. 6.5 liters compressor rotary compressor refrigerant R290 / 180 g Dimensions (H x W x D) 64.5 x 40 x 31 cm Weight 24 kg cessation of operations Digital ambient temperature Manufacturer's information: 5°C - 35°C (our recommendation: 7°C ~ 35°C) application area general room dehumidification: up to approx. 200m² Laundry drying: dries 6-8 washing machine loads per day Swiss plug: Yes hose connection Yes guarantee 2 years

Read more less

An inexpensive, powerful dehumidifier with a kWh consumption meter, especially for water damage restoration and zones with permanently high humidity levels. The "35B" was specially developed to quickly dry water damage, e.g. after high water or flooding. It has a very strong dehumidification capacity, a consumption meter (kWh) and an on/off switch. A hygrostat for regulating the target humidity was deliberately omitted in this version. Recommended room size up to 90m², from 8°C. The performance and drying speed can be further accelerated with free-standing fans if required (e.g. FN45 from our range). Characteristics • Dehumidification capacity of up to 35 liters / day (at 30°C/80% RH). • Function for continuous operation/continuous dehumidification. • Calibrated (MID) consumption meter (kWh). • On/off toggle switch. • Equipped with a highly efficient rotary compressor. This compressor is one of the most powerful compressors on the market. • Automatic professional defrost function. • Removable condensate tank. • Possibility of connecting a hose for continuous drainage of the condensate. • Powder coated metal housing/metal frame. • Very easy mobility thanks to transport handles and large tires for safe travel over steps and uneven ground. • Operating warning light / defrost light. • No separate or additional coolant is required (closed circuit). • Cleanable air filter grille. • CFC free and meets WEEE standards.     usage examples Construction and industrial dryers : Thanks to their handy design, they are ideal for drying on construction sites with at least slightly temperate temperatures and in industry. Drying out water damage : Due to its powerful dehumidification performance, the 35b is often used to dry out water damage. Easy billing of consumption with insurance companies thanks to the integrated kWh consumption meter. dehumidification performance The dryer can be used over a temperature range between +8°C and +35°C, preferably in at least slightly temperate rooms from 8°C and higher. As with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: 30°C/80% RH: approx. 35 liters / 24 h (at 60% RH: approx. 18 liters) 20°C/80% RH: approx. 18 liters / 24 h (at 60% RH: approx. 11 liters 15°C/80% RH: approx. 14 liters / 24 h (at 60% RH: approx. 8 liters) 10°C/80% RH: approx. 9 liters / 24 h (at 60% RH: approx. 6 liters) (RH=relative humidity) Technical data  Tension 220-240V / 50Hz power consumption max. 450 (2.0 A) or 360W (at 20°C/60% RH) sound pressure level 56 dB(A) (manufacturer information) dehumidification performance max. 35 liters/day (30°C / 80% RH) amount of recirculated air 230 m³/h (built-in) condensate tank approx. 4.6 liters (direct hose connection possible) compressor rotary compressor refrigerant R290C (135gr.) Dimensions (H x W x D) 780 x 420 x 420 mm Weight: 22 kg Operating setting: ON/OFF toggle switch Ambient temperature: 8°C ~ 35°C Application area: up to 90m² Swiss plug: EU plug with fixed adapter for Switzerland hose connection: Yes Guarantee: 2 years

Read more less

Semi-professional dehumidifier for basements, construction sites and laundry drying   This comfort dehumidifier protects and preserves what is dear to you. It is suitable for powerful dehumidification tasks in the basement and laundry room, as well as for professional use for drying water damage or keeping construction sites dry. Thanks to hot gas defrosting, it is also recommended for optimal drying results at low temperatures.     The all-rounder: Protects against mold, corrosion and structural damage Excess humidity in the room air (> 60 percent) provides an ideal environment for pathogens. At this level, mold also spreads in the living space and increases the risk of respiratory disease. Vintage cars in the garage, works of art on the walls and archived documents and books also suffer from excessive humidity. There are many causes of harmful humidity: defects in the building's waterproofing, inadequate ventilation, storms, floods or leaks in water pipes. The 122E keeps you dry.     Compact design – outstanding dehumidification performance Whether as a room climate improver in a private environment or as a construction dryer in commercial use - the cuboid-shaped stainless steel dehumidifier impresses with its convenient features (e.g. 24-hour timer and auto-restart function as well as a control panel lock function), an 8-liter condensate container and a strong dehumidification capacity of 38 l/24 h at 240 m³/h air volume - sufficient for room sizes of up to 100 m² or 250 m³. Thanks to the auto-restart function (memory function), the device automatically starts in the preselected settings after a brief power cut. For maximum operating comfort, the control panel is equipped with easy-care membrane buttons and a digital display of the room temperature and humidity. The target humidity is preselected in 5 percent increments. The standard equipment also includes a level warning light when the water tank is full, overfill protection with automatic shut-off and a reusable air filter that is easy to clean.     Gentle laundry drying with dehumidifiers In addition to dehumidifying the air in the room, a dehumidifier can be used conveniently to dry laundry - as a supplement or as a complete replacement for a conventional tumble dryer. The laundry drying function (or textile drying mode or SuperDry function) is comparable to traditional air drying outdoors. Dehumidifiers offer the advantage that laundry is dried gently, just like in nature. Colors stay bright and clothes last longer than with conventional tumble dryers, while using significantly less electricity. In addition, sensitive materials such as wool, silk or synthetic fibers can be dried without any problems. In contrast to pure air drying, the laundry becomes much softer and more comfortable to wear on the skin.    environmentally friendly refrigerant R290 Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and is a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Additional benefit for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.     A dehumidifier for all occasions • Ideal for a healthy living environment in living areas • Moisture protection in archives, libraries and art exhibitions • Corrosion and mold protection in (classic car) garages, basements and storage rooms • Drying of construction sites and drying of damp masonry after water damage     connection for external condensate drain For applications where regular emptying of the 8-litre condensate container is either not possible or undesirable, for example when using the dryer for unattended continuous drying in the basement, garage, holiday home or on boats, the dryer has an integrated hose connection for direct drainage of the condensate into a drain. A short piece of suitable hose is already included in the scope of delivery.     Hot gas defrosting for faster drying results In low temperature ranges (below 12 °C), the integrated hot gas automatic defrosting system ensures consistently reliable air dehumidification - without long defrosting phases. In contrast to the time-consuming circulating air defrosting of normal condenser dryers, defrosting is carried out by introducing hot gas into the evaporator. This significantly shortens the duration of defrosting and the drying target is achieved more quickly.     SuperDry function for accelerated textile drying The special SuperDry function is practical for quickly dehumidifying wet laundry, clothing or carpets. This means that even large textiles that don't fit in the dryer can be dried in no time.    Advantages at a glance • Quality hot gas automatic defrosting • SuperDry function for accelerated textile drying • Automatic hygrostat-controlled dehumidification operation with real-value humidity preselection • Activated carbon filter against unpleasant odors • 24-hour timer • Auto-restart function (memory function) • suitable for building drying • suitable for keeping damp cellars dry • suitable for drying laundry • Permanent mode • Easy-care material mix with a striking look • Digital display of the current humidity and temperature values • Control panel lock function (child lock)     Technical data   dehumidification performance at 30 °C / 80 % RH 38 liters / day air volume 240 m³/h Maximum room size 100 m² (100 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 35°C humidity range 30 - 90 % RH voltage 220 - 240 V/50 Hz nominal current consumption max. 2.9 A power consumption max. 750W Recommended coverage 10 A cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (96g) GWP3 water bucket 8 liters operating noise 52 dB(A) at 1 m distance 49 dB(A) at 2.5 m distance Dimensions L x W x H 453 x 310 x 635 mm Weight 27.5 kg defrosting automatic hot gas automatic dehumidification hygrostat-controlled fan axial, 2-stage fan automatic shutdown when bucket is full Yes prefilter Yes timer Yes continuous operation possible Yes laundry drying mode Yes display shows current room humidity, set humidity memory function yes (saves set values ​​automatically) hose connection yes, short hose piece included guarantee 2 years  

Read more less

Powerful dehumidifier / construction dryer 50B-WDH with calibrated consumption meter. The "50B" was specially developed to quickly dry water damage, e.g. after high water or flooding. It has a very strong dehumidification capacity and only an on/off switch for optimal operation on construction sites and when drying water damage. A hygrostat for regulating the target humidity was deliberately omitted in this version. Recommended room size up to 120m², from 8°C. The performance and drying speed can be further accelerated with free-standing fans if required (e.g. FN45 from our range). Characteristics • Dehumidification capacity of up to 42 liters / day (at 30°C/80% RH) • Function for continuous operation/continuous dehumidification • calibrated consumption meter (kWh) • On/off toggle switch • Equipped with a highly efficient rotary compressor. This compressor is one of the most powerful compressors on the market • Automatic professional defrost function • Removable condensate tank • Possibility of connecting a hose for continuous drainage of the condensate • Powder-coated metal housing/metal frame • Very easy mobility thanks to transport handles and large wheels for safe travel over steps and uneven ground • Operating warning light / defrost light • No separate or renewed coolant is required (closed circuit) • Cleanable air filter grille • Environmentally friendly refrigerant R290 • CFC free and compliance with WEEE standards Important The "50B" construction dryer is not suitable for use in very cold rooms, as the powerful dehumidification unit can cause it to freeze up during continuous operation below 8°C.   dehumidification performance The dryer can be used over a temperature range between +8°C and +32°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: 30°C/80% RH: approx. 42 liters (at 60% RH: approx. 21 liters) 20°C/80% RH: approx. 21 liters (at 60% RH: approx. 12 liters 15°C/80% RH: approx. 15 liters (at 60% RH: approx. 8 liters) 10°C/80% RH: approx. 8 liters (at 60% RH: approx. 6 liters) (RH=relative humidity) Technical data  Tension 220-240V / 50Hz Power consumption: max. 820 (3.7 A) or 620W (at 20°C/60% RH) Sound pressure level: 57 dB(A) (manufacturer information) dehumidification performance 42 liters/day (30°C / 80% RH) amount of recirculated air 400 m³/h (built-in) condensate tank about 5 liters (direct hose connection possible) compressor rotary compressor refrigerant R290 (230gr.) Dimensions (H x W x D) 890 x 450 x 740 mm Weight 32 kg cessation of operations ON/OFF toggle switch ambient temperature 8°C ~ 32°C application area Rooms from min. 10m² to max. 120m² Swiss plug: EU plug with fixed adapter for Switzerland hose connection Yes guarantee 2 years

Read more less

Perfect all-rounder for construction, trade and water damage restoration   This Trotec dehumidifier impresses with its powerful dehumidification performance combined with a strong fan that blows the dried air back into the room at high speed. This means that the room air is circulated optimally and drying is significantly faster, especially in large, very humid archive and storage rooms or those with shelves.   The trolley construction with guide handles, carrying troughs and large wheels facilitates transport even in difficult terrain or on steps.   The dryer has an easy-care control panel with a digital display of all functions for quick start-up. For hygrostat-controlled automatic operation, the target can be preselected in percentage increments, which is then displayed together with the current actual value. The selectable target humidity range is 20 - 90%, although in practice values ​​below 35% are difficult to achieve. This device develops its full power in rooms that are at least slightly temperate; 12 °C or higher is ideal.   The timer can be used to configure the switch-on or switch-off time, and thanks to the integrated memory function, the settings are retained even after a power failure. This means that operation with a timer is also possible.     bucket and direct hose connection The water extracted from the air is collected in a 5.5 liter bucket. A magnetic float automatically stops operation when the bucket is full and a warning light indicates visually that the bucket should be emptied. A hose can be connected to the bucket itself if necessary if the water can be drained away directly. The hose must be laid in a downward direction as there is no pump integrated into the dryer (we can optionally supply a free-standing condensate pump if the water can or should be pumped up or away.     With optional air hose connection for cavity drying   Whether in suspended ceilings, bathtub cavities, cassette walls or cable ducts - if moisture has penetrated into hard-to-reach cavities, action should be taken quickly to prevent mold from forming. This dehumidifier is also suitable for this, as it is equipped with a particularly powerful fan with 3.2 MPa air pressure. An air hose with a suitable adapter can optionally be attached to this so that the dry air is directed precisely to the damp areas.   Note: If there is a lot of dirt, dust or mold in the cavity, the room should not be occupied or used during this drying process, as otherwise the dust particles and mold spores can spread everywhere. In this case, the additional use of an air purifier is recommended.     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection.   The natural refrigerant propane (R290) is an organic compound and is classified as a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Additional benefit for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.     Advantages at a glance   • Particularly economical solution for typical dehumidification applications in the commercial sector • High dehumidification performance even at low temperatures • Air hose connection for selective dry air application or cavity drying • Robust steel construction in trolley design • Can be transported and stored in any position thanks to the rotary piston compressor • Timer function • Memory function (auto-restart function) • Permanent mode for continuous operation • Maintenance-friendly magnetic locking door   Technical data   dehumidification performance at 30 °C / 80 % RH 51 liters / day air volume 450 m³/h Maximum room size 130 m² (330 m³) Minimum room size 12 m² (30 m³) temperature range 5 - 30°C humidity range technically humidity range practice 20 - 90 % RH 35 - 90% RH (finned evaporator) voltage 220 - 240 V/50 Hz nominal current consumption max. 2.7 A power consumption max. 650W Recommended coverage 10 A cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R290 (230g) GWP3 water bucket 5.5 liters operating noise 52 dB(A) at 1 m distance 49 dB(A) at 2.5 m distance Dimensions D x W x H 525 x 490 x 900 mm Weight 40 kg defrosting automatic recirculation, electronic automatic dehumidification hygrostat-controlled fan radial, 1-stage fan automatic shutdown when bucket is full Yes prefilter Yes timer Yes continuous operation possible Yes display shows current room humidity, set humidity memory function yes (saves set values ​​automatically) hose connection yes, no hose included guarantee 2 years

Read more less

The Oasis dehumidifiers are among the most widely used drying devices that have been used successfully for many years on construction sites and by private users. The devices have now been revised and adapted to the latest state of the art with the latest, environmentally friendly refrigerant R290 and improved efficiency. The Oasis D165 is suitable for basements and rooms up to 90m² and has a large bucket and direct hose connection as standard. Although visually very similar, the D165 dehumidifier has been completely redesigned in several respects compared to its predecessor: • improved efficiency • higher dehumidification performance • environmentally friendly refrigerant R290 • improved automatic self-defrosting, therefore usable down to 5°C (previously: 8°C) • reinforced front cover with spark protection shell • reinforced, durable rollers The dryer stands on 4 castors, but can also be attached to the wall on a suitable wall bracket available from us. The air intake area is at the back, where a filter cleans the moist air. The filter itself is easy to remove and clean. The dry air is blown out into the room at the front. The Oasis is therefore ideal for general humidity control in a classic basement environment, for example in new buildings, but also for unattended continuous operation in temperature-controlled archives and on construction sites. The fan is rather too weak for active laundry drying. The target humidity is regulated using a continuously variable hygrostat wheel on the front. When the set value is reached, dehumidification pauses (ventilation also stops) until the humidity rises again. Operation continues with the same setting even after a power failure. This means that the D165 is also suitable for operation with a timer if, for example, you only want to run the dryer during low tariff periods. Thanks to the tube evaporators, the D165 extracts water from the air down to low humidity levels. The water is collected in the tank pushed into the back; a float mechanically stops operation when the tank is full. Alternatively, a hose can be screwed onto the condensate collecting tray (with a coupling/3/4 inch thread), whereby the hose must have a gradient towards the drain (no pump integrated in the device). usage examples Cellar damp : Ideal for damp cellars, old walls and laundry rooms. Eliminates musty smells, stops mold growth, decomposition of masonry and much more. Construction and industrial dryers : thanks to their handy, robust design, they are ideal for drying on construction sites and in industry. Drying out water damage : The Oasis uses tube evaporators to remove water from the air even in areas of low humidity. This significantly accelerates the drying out of water damage. dehumidification performance Thanks to hot gas defrosting, the dryer can be used over a wide temperature range between +5°C and +32°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions:   30°C/80% RH: 28 liters / 24 h 27°C/60% RH: 16.8 liters / 24 h 20°C/60% RH: 10.8 liters / 24 h 10°C/70% RH: 5.3 liters / 24 h (RH=relative humidity)    Massive improvement in environmental compatibility The GWP (Global Warming Potential - influence on global warming) was reduced by a factor of 800 (!) from 1430 (R134a) to less than 2 (R290). Furthermore, the D165 requires 10% less electricity while simultaneously increasing dehumidification performance by 14% (at room temperature 20°C, 60% RH). Technical data  Tension 230V / 50Hz power consumption max. 360W sound pressure level 1 m distance 54 dB(A) (our measurement) 2.5 m distance 51 dB(A) (our measurement) dehumidification performance max. 28 liters/day (30°C / 80% RH) Bucket Capacity 9 liters, approx. 8 liters until operation interrupted by float compressor rotary compressor refrigerant R290 (150gr.) Dimensions (H x W x D) 60 x 38 x 36 cm (including wheels) Weight 23.5 kg cessation of operations hygrostat wheel ambient temperature 5°C ~ 40°C application area up to approx. 90m² Swiss plug Yes hose connection Yes operating hour meter Yes guarantee 2 years  

Read more less

This construction dryer is very popular in professional use because it has a strong dehumidification capacity of up to 30 liters per day and at the same time, at less than 20 kg, is one of the lightest dehumidifiers in this category. This means that it can be easily transported by one person up stairs and even over scaffolding to the drying location.   It is also compact in size, which saves space in the service vehicle. This is very much appreciated by water damage repairers who have to bring a lot of equipment to the damage site in the shortest possible time.   This model is also impressive when it comes to storage, as it is stackable and therefore takes up less space in the warehouse.     Operation   The desired target moisture can be selected in 1% increments using the digital control panel on top of the device. Continuous operation is also possible. The set values ​​are saved by pressing the memory button. In the event of a power failure, operation will automatically continue with the same settings as soon as the power is restored. An operating hour counter on the side provides information on the drying time.   The moist room air is sucked in at the back and cleaned of dust and dirt by an easy-to-clean filter. The dried air is then blown out at the front. The automatic hot gas defrosting ensures that dehumidification takes place with maximum efficiency even in cooler environments.   The water extracted from the air can either be collected in the inserted bucket or drained directly via a hose (suitable inner diameter: 10 mm). A float automatically stops operation when the bucket is full. If the water is drained via the hose, it first runs through the bucket to which the hose connector is attached. This system is very safe: if the hose is blocked, kinked or not laid correctly, the water backs up into the bucket. When the bucket is full, operation stops. This means that overflowing onto the floor is not possible, unlike dryers where the hose is attached directly to the drip tray.     Important functions   • Digital control and side-mounted operating hour counter • High efficiency thanks to automatic hot gas defrosting • Robust housing with foldable carrying handle and four small wheels • Easy to use • Built-in hygrostat • Water tank with automatic shutdown when tank is full • Possibility to connect a hose for direct drainage of condensate • Air filter • Stackable     Suitable for  • Keeping private cellars and rooms dry • Keeping commercial premises and archives dry • Construction • Industry and Production • Rental • Construction and water damage drying • Waterworks  Propane (R290) as an environmentally friendly refrigerant in dehumidifiers Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and is classified as a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).  Additional benefit for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.     Technical data   dehumidification performance at 20 °C / 60 % RH at 30 °C / 80 % RH   10.8 liters / day 30 liters / day air volume max. 200 m³/ h Maximum room size 75 m² (180 m³) temperature range 5 - 35 °C humidity range technically humidity range practice 35 - 90 % RH 40 - 90% RH (finned evaporator) voltage 220 - 240 V/50 Hz nominal current consumption max. 3 A power consumption max. 680 W Recommended coverage 10 A Plug connection cable with EU plug and Swiss fixed adapter refrigerant R290 (GWP: 3) bucket + hose connection 6.5 liter bucket and direct hose connection (suitable hose 10mm inner diameter) operating noise 45 dB(A) at 1 m distance 42 dB(A) at a distance of 3 m dimensions (W x H x D) 338 x 550 x 358 mm Weight 19.5 kg automatic defrosting hot gas Attitude Digital control panel fan axial, 1-stage fan compressor rolling piston prefilter Yes operating hour meter Yes continuous operation possible Yes display Yes memory function yes (set values ​​saved at the touch of a button) guarantee 2 years

Read more less

The universal all-rounder   Whether drying out after water damage, drying out new buildings or keeping heated and unheated storage rooms dry - the 170S is a universally applicable dehumidifier with high-quality workmanship and reliable operation. It is manufactured in a specialized factory in Europe. It is built to last, is easy to care for, requires little maintenance and is very affordable considering its power and quality .     Easy operation   The desired target humidity can be continuously regulated between 32 - 100% using a mechanical hygrostat; continuous operation is also possible. The high air circulation volume of an impressive 580 cubic meters per hour is particularly useful in larger zones. With its stable carriage construction and large wheels, frequent changes of location can be carried out very easily.     bucket, direct hose connection and optional pump kit   The water that is extracted from the air flows into the 6-litre bucket. This is on a scale that automatically stops operation when it is full. A control lamp indicates that the bucket is full. It is also possible to connect a hose if the water can be drained away directly. In this case, the hose must have a gradient towards the drain. If this is not possible, a suitable pump kit is available as an option, with which the water can be pumped up and away.   The operating switch and level warning light are protected against dust and splash water by a protective cap and a slotted hygrostat rotary switch protects against accidental adjustment of the switch position.     Professional hot gas defrosting   Inside, a professional hot gas automatic defrosting system ensures effective dehumidification results. The finned evaporators are particularly effective in temperatures above 10°C and in humidity levels above 40%. Technically, the dryer can also be used in lower temperatures down to around 5°C, even in unattended continuous operation.     Optional counters   The delivery does not include an hour or consumption meter. You can order these from us if you wish (the housing is prepared for retrofitting as standard). You can choose between a pure hour meter or the combined dual meter, which measures hours and power consumption. The meters are MID-compliant. Outside Switzerland, dryers used professionally must already be MID-compliant.     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and is a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Additional benefit for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.     Advantages at a glance   • High dehumidification performance even at low temperatures • Robust plastic-coated metal housing • Can be transported and stored in any position thanks to the rotary piston compressor • Stable carriage construction • Automatic hygrostat-controlled dehumidification operation • Quality hot gas automatic defrosting • Possibility of retrofitting MID-compliant dual meters for operating hours and kilowatt hours (optional) • Possibility to add a suitable pump kit, which can be connected directly to the device (optional)     Technical data   dehumidification performance at 30 °C / 80 % RH 40 liters / day air volume 580 m³/h Maximum room size 100 m² (250 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 32°C humidity range technically humidity range practice 32 - 90 % RH 40 - 90 % RH voltage 220 - 240 V/50 Hz nominal current consumption max. 2.8 A power consumption max. 600W Recommended coverage 10 A cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R290 (150g) GWP3 water bucket 6 liters operating noise 52 dB(A) at 1 m distance 49 dB(A) at 2.5 m distance Dimensions D x W x H 540 x 490 x 963 mm (including guide bracket) Weight 32 kg defrosting automatic hot gas automatic dehumidification hygrostat-controlled fan axial, 1-stage fan automatic shutdown when bucket is full Yes prefilter Yes timer no (operation with timer possible) continuous operation possible Yes memory function yes (saves set values ​​mechanically) hose connection yes (no hose included) - 12 mm pump optionally available (not included) guarantee 2 years

Read more less

With its powerful dehumidification performance, this professional construction dryer can handle even the most demanding tasks. The integrated condensate water pump ensures comfortable operation, as the water that accumulates is automatically drained away. You also get other professional functions such as an operating hour counter, a temperature display, a humidity display and an automatic defrost function. Considering its dehumidification power, it is economical in consumption and has the new refrigerant "R290", which has a minimal impact on the environment. The "Global Warming Potential (GWP)" is 3, which corresponds to a reduction of 99.85% compared to comparable models of previous generations. service The control panel is located at the front of the housing and offers various options:     setting target humidity The desired target humidity is set at the touch of a button, i.e. the value at which the device should keep the room stable. If the measured humidity in the room is higher, the device will operate. If the humidity is correct, the device pauses, and not only the compressor but also the fan stops. The desired target humidity can be selected in 5% increments between 10 - 90%, with the setting at 10% corresponding to continuous operation. To protect a room from mold and odors, a value of around 60% is sufficient, so the ideal setting is 50 or 55%. Lower values ​​do not provide any additional benefit, unless you are drying out water damage.  timer With the timer, operation can either be limited to a time "from now" (1-24 hours) or started at a time 1-24 hours in the future, for example if you want to start operation at the low tariff.  memory function If you want to run the device at the same time every day (for example during off-peak hours), you can do this with a standard timer. The dryer remembers the last setting and returns with the same settings after a power outage.     pump  Instead of a bucket, this model has an integrated water pump that pumps away the condensate that is removed. The hose included in the delivery is 7.5m, but can also be extended. If the hose is laid flat, the water can easily cover distances of up to 20m. When pumping upwards, the possible distance is reduced depending on the height difference. A check valve prevents water standing in the hose from flowing back into the device. The device itself contains a small tank that can be completely pumped out at the touch of a button before transport.     Advantages at a glance   • Dehumidification capacity of up to 65 liters/day • Professional operating hour counter for monitoring the operating time • The delivery includes 7.5 meters of condensate hose including a check valve • Temperature display (input / output) to monitor the ambient conditions • Integrated pump function that allows you to pump out the condensate up to a discharge height of 3 meters • Automatic continuation of operation after a power failure • Equipped with a highly efficient rotary compressor for maximum performance and energy efficiency • Clear LED display including humidity indicator for easy operation and control • Humidity control in 5% steps between 10% to 90% for precise drying results • Automatic professional defrost function to prevent ice formation in the cooling system • Timer function per hour for flexible drying time • Stackable to save space for easy transport and storage • Two semi-pneumatic tires for easy transport • CE (EMC + LVD) conformity and “GS” tested.     scope of delivery   • Construction dryer • Power cable • Condensate hose with check valve • Operating instructions   dehumidification performance The dryer can be used over a wide temperature range between +5°C and +35°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of approximate dehumidification performance under different (constant) ambient conditions: 30 °C: 80% humid: 65 liters / 24 hours - 60% humid: 42 liters / 24 hours 20 °C: 80% moisture: 32 liters / 24 hours - 60% moisture: 24 liters / 24 hours 15 °C: 80% moisture: 23 liters / 24 hours - 60% moisture: 17 liters / 24 hours 10 °C: 80% moisture: 13 liters / 24 hours - 60% moisture: 12 liters / 24 hours    Technical data  Tension 220-240V / 50Hz power consumption max. 850 (3.7 A) or 710W (3.1 A) at 20°C/60% RH sound pressure level 55 dB(A) (manufacturer's information) dehumidification performance max. 65 liters/day (30°C / 80% RH) amount of recirculated air 350 m³/h, 1 ventilation level condensate tank No tank, integrated pump with 7.5 m hose compressor rotary compressor refrigerant R290C (250gr.) Dimensions (H x W x L) 470 x 325 x 600 mm Weight: 39 kg Operating setting: Digital control panel Ambient temperature: 5°C ~ 35°C Application area: up to 150 m² Swiss plug: EU plug with fixed adapter for Switzerland hose connection: Yes Guarantee: 2 years

Read more less

Powerful dehumidifier/construction dryer with metal housing. For powerful drying of larger rooms and water damage. Characteristics • Dehumidification capacity of up to 50 liters / day • Electric hygrostat (LED) for regulating and setting the desired humidity • Function for continuous operation/continuous dehumidification • Electricity consumption meter (kWh) • Operating hour counter • Automatic memory function, saves the settings for automatic operation after a power failure • Clear display including actual humidity, target humidity and status overview • Equipped with a highly efficient rotary compressor. This compressor is one of the most powerful compressors on the market • Automatic professional defrost function • Humidity control of seamless 1% steps between 30% to 90% (plus continuous operation function) • Removable condensate tank • Possibility of connecting a hose for continuous drainage of the condensate • Powder-coated metal housing/metal frame • Very easy mobility thanks to transport handles and large wheels for safe travel over steps and uneven ground • Operating warning light / defrost light • No separate or renewed coolant is required (closed circuit) • Cleanable air filter grille • Environmentally friendly refrigerant R290 • CFC free and compliance with WEEE standards notes Not suitable for use in very cold rooms, as the cooling element can freeze up if used continuously below 8°C. Unlike similar models on the market, the ventilation also stops when the desired target humidity is reached, which means less power consumption with the same performance. dehumidification performance Overview of the approximate dehumidification quantities in liters per day at different room temperatures and humidity: 30 °C / 80% RH = approx. 50 L (60% RH = approx. 25 L) 20 °C / 80% RH = approx. 25 L (60% RH = approx. 14 L) 15 °C / 80% RH = approx. 18 L (60% RH = approx. 10 L) 10 °C / 80% RH = approx. 10 L (60% RH = approx. 7 L) (RH=relative humidity) (akd) Tension 220-240 V / 50 Hz power consumption max. 820 (3.7 A) / 700 W (3.2 A) at 20 °C / 60% RH sound pressure level 57 dB(A) (manufacturer information) dehumidification performance 50 liters/day (30 °C / 80% RH) amount of recirculated air 350 m³/h (built-in) condensate tank approx. 5.5 liters (direct hose connection possible) compressor rotary compressor refrigerant R290 (230gr.) Dimensions (H x W x D) 925 x 605 x 462 mm Weight 31 kg cessation of operations Digital ambient temperature 8 °C ~ 32 °C application area min. 11 m² to max. 120 m² Swiss plug Yes hose connection Yes guarantee 2 years

Read more less

The compact dimensions combined with the powerful dehumidification performance make this model ideal for drying out buildings and drying out water damage. The dehumidifier is also suitable for keeping commercial properties, archives and production rooms dry. With its two large castors and a guide bar, it is easy to move around objects.   Operation  The desired target humidity can be selected in 1% increments between 40-80% using the digital control panel on the front. Continuous operation is also possible. The set values ​​can be saved at the touch of a button. In the event of a power failure, operation will automatically continue with the same settings as soon as the power is restored. The moist room air is sucked in at the front and cleaned of dust and dirt by an easy-to-clean filter that can be pulled out upwards. The dried air is then blown out to the back. The display shows the currently measured humidity.  The water extracted from the air can either be collected in the inserted bucket or drained directly via a hose (suitable inner diameter: 12 mm). A float automatically stops operation when the bucket is full. If the water is drained via the hose, it first runs through the bucket to which the hose connector is attached. This system is very safe: if the hose is blocked, kinked or not laid correctly, the water backs up into the bucket. When the bucket is full, operation stops. This means that overflowing onto the floor is not possible, unlike dryers where the hose is attached directly to the drip tray.     Important functions   • Digital control and side-mounted operating hour counter • High efficiency thanks to automatic hot gas defrosting • Robust housing with two large rollers and guide bracket • Easy to use • Built-in hygrostat • Water tank with automatic shutdown when tank is full • Possibility to connect a hose for direct drainage of condensate • Air filter     Suitable for  • Keeping commercial premises and archives dry • Drying of water damage • Building drying • Industry and Production • Rental  Propane (R290) as an environmentally friendly refrigerant in dehumidifiers Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection.  The natural refrigerant propane (R290) is an organic compound and is classified as a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3). Additional benefit for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.     Technical data   dehumidification performance at 20 °C / 60 % RH at 30 °C / 80 % RH   20.3 liters / day 45.6 liters / day air volume max. 350 m³/ h Maximum room size 115 m² (280 m³) temperature range 5 - 35 °C humidity range technically humidity range practice 35 - 90 % RH 40 - 90% RH (finned evaporator) voltage 220 - 240 V/50 Hz nominal current consumption max. 4 A power consumption max. 900 W Recommended coverage 10 A Plug connection cable with EU plug and Swiss fixed adapter refrigerant R290 (GWP: 3) bucket + hose connection 5.7 liter bucket and direct hose connection (suitable hose 12mm inner diameter) operating noise 55 dB(A) at 1 m distance 52 dB(A) at 3 m distance dimensions (W x H x D) 422 x 820 x 580 mm Weight 30 kg automatic defrosting hot gas Attitude Digital control panel fan axial, 1-stage fan compressor rolling piston prefilter Yes operating hour meter Yes continuous operation possible Yes display Yes memory function yes (set values ​​saved at the touch of a button) guarantee 2 years

Read more less

Professional construction dryer with large bucket   A high-quality dehumidifier for commercial use and for drying out water damage, made in Europe. Its impressive external appearance is in no way inferior to its inner values: All electrical components are specially encapsulated and thus protect the electronics from harmful deposits that could impair their function and longevity. This dryer is therefore also ideal for use under demanding conditions. Thanks to its maintenance-friendly design, it is easy to care for.   Compared to cheaper reciprocating piston compressors, the high-quality 0.58 kW rotary compressor installed here offers the advantage of higher performance with comparatively lower power consumption - and also creates reserves for high dehumidification performance even in unheated rooms. In addition, the high-quality hot gas automatic defrosting system ensures a much more efficient dehumidification performance compared to other defrosting systems, without time-related defrost breaks during which no dehumidification takes place.     Propane (R290) as an environmentally friendly refrigerant in dehumidifiers   Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using propane (R290) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection. The natural refrigerant propane (R290) is an organic compound and is a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly propane (R290) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=3).   Additional benefit for the environment: Due to its excellent thermodynamic properties, propane (R290) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.     User-friendly   Thanks to its robust housing, ergonomic recessed handles with an internal grip clip and four stable steering wheels with roll stops, the device is ideal for use on construction sites and for drying water damage. However, these advantages are also appreciated in commercial premises or in private basements.   The storage is also well thought out: two practical stacking grooves on the top of the device enable stable and space-saving stacking during transport and in storage.     An integrated operating hour counter reliably documents the exact operating time, even during longer drying operations.     Integrated compressor heat protection with automatic switch-off   When drying with extremely high humidity and high temperatures - for example when repairing water damage - refrigeration dryers quickly reach their red performance range. The catchy "35 rule" applies here: drying water damage at temperatures above 35 degrees reduces the dryer's service life to less than 35%. However, this is not a question of component quality, but pure physics, which applies to all refrigeration dryers on the market regardless of the manufacturer. While most professional condenser dryers can still work easily up to 35 °C at moderate humidity of around 70% RH, very high humidity combined with a high room temperature means that significantly more energy is added to the moist room air, which must also be "worked off" via the refrigerant. As a result, the pressure of the refrigerant in the system increases immensely, which leads to a destructive load on the compressor. The dehumidifiers will initially continue to work, but well above their limit "deep in the dark red range", which results in an extremely shortened remaining service life. That's why the TTK-S series commercial dehumidifiers have integrated compressor heat protection to actively preserve the value of your devices: Sensors constantly monitor the heat load of the compressor. If the temperature is within the defined working range, the integrated heat protection display pulses in a long sequence, indicating that the dehumidifier is operating optimally. As soon as the temperature exceeds the critical limit of 35 °C, the automatic system switches the compressor off to protect it, while the fan continues to operate, and automatically reactivates the compressor as soon as the temperature falls below the 35° limit again. This protection not only significantly extends the service life of the dehumidifier, it also prevents thermal damage to materials in the room and the building structure when they are in use.     options   • Dual meter available for additional recording of power consumption. • powerful condensate pump for permanent drying with a pumping capacity of up to 50 m and a maximum discharge head of 4 m     Advantages at a glance • High dehumidification performance even at low temperatures • Maximum dust and moisture protection for all electrical components • Extremely maintenance-friendly design • Optimal handling properties • Can be transported and stored in any position thanks to the rotary piston compressor • Practical stacking groove for stable, space-saving storage and transport • Multi-stacking capability with identical models • Practice-optimized industrial design • Made in Europe     Technical data   dehumidification performance at 30 °C / 80 % RH 28 liters / day air volume 250 m³/h Maximum room size 70 m² (175 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C humidity range 35 - 90 % RH voltage 220 - 240 V/50 Hz nominal current consumption max. 2.3 A power consumption max. 500W Recommended coverage 10 A cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R290 (150g) GWP3 water bucket 6 liters operating noise 52 dB(A) at 1 m distance 49 dB(A) at 2.5 m distance Dimensions L x W x H 375 x 345 x 603 mm Weight 26 kg defrosting automatic hot gas automatic dehumidification hygrostat-controlled fan axial, 1-stage fan automatic shutdown when bucket is full Yes prefilter Yes timer no continuous operation possible Yes memory function yes (saves set values ​​mechanically) hose connection yes, short hose piece included guarantee 2 years    

Read more less

The robust and powerful all-rounder   Whether drying out after water damage, drying out new buildings or keeping heated and unheated storage rooms dry - the 350S is a universally applicable dehumidifier with high-quality workmanship and reliable operation. It is manufactured in a specialized factory in Europe. It is built to last, is easy to care for, requires little maintenance and is very affordable considering its power and quality.  Easy operation  The desired target humidity can be continuously regulated between 32 - 100% using a mechanical hygrostat; continuous operation is also possible. With the finned evaporator used, target humidity levels below 40% RH are difficult to achieve, but this technology shows impressive dehumidification power in temperate and humid environments. The high air circulation volume of an impressive 1000 cubic meters per hour is particularly useful in larger zones. With its stable carriage construction and large impellers, frequent changes of location can be carried out very easily.  bucket, direct hose connection and optional pump kit  The water that is extracted from the air flows into the 6-litre bucket. This is on a scale that automatically stops operation when it is full. A control lamp indicates that the bucket is full. It is also possible to connect a hose if the water can be drained away directly. In this case, the hose must have a gradient towards the drain. If this is not possible, a suitable pump kit is available as an option, with which the water can be pumped up and away. The operating switch and level warning light are protected against dust and splash water by a protective cap and a slotted hygrostat rotary switch protects against accidental adjustment of the switch position.     For continuous operation on construction sites   Thanks to the option of connecting an external condensate drain – with an optional condensate pump if required – the construction dryer is also ideal for longer, unattended drying tasks, e.g. during construction drying.     Optional counters  The delivery does not include an hour or consumption meter. You can order these from us if you wish (the housing is prepared for retrofitting as standard). You can choose between a pure hour meter or the combined dual meter, which measures hours and power consumption. The meters are MID-compliant. Outside Switzerland, dryers used professionally must already be MID-compliant.     Hydrofluoroolefin (R-454C) as an environmentally friendly refrigerant in dehumidifiers   Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using hydrofluoroolefin (R-454C) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection.   The natural refrigerant hydrofluoroolefin (R-454C) is an organic compound and is classified as a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly hydrofluoroolefin (R-454C) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=146).   Additional benefit for the environment: Due to its excellent thermodynamic properties, hydrofluoroolefin (R-454C) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.     Advantages at a glance • High dehumidification performance even at low temperatures • Robust plastic-coated metal housing • Can be transported and stored in any position thanks to the rotary piston compressor • Stable carriage construction • Automatic hygrostat-controlled dehumidification operation • Quality hot gas automatic defrosting • Possibility of retrofitting MID-compliant dual meters for operating hours and kilowatt hours (optional) • Possibility to add a suitable pump kit, which can be connected directly to the device (optional)     Technical data   dehumidification performance at 30 °C / 80 % RH 55 liters / day air volume 1000 m³/h Maximum room size 140 m² (350 m³) Minimum room size 8 m² (20 m³) temperature range 5 - 32°C humidity range technically humidity range practice 32 - 90 % RH 40 - 90 % RH voltage 220 - 240 V/50 Hz nominal current consumption max. 6.1 A power consumption max. 1400W Recommended coverage 10 A cable length approx. 3 m Plug EU plug with Swiss adapter refrigerant R454C (650g) GWP146 water bucket 6 liters operating noise 54 dB(A) at 1 m distance 51 dB(A) at 2.5 m distance Dimensions D x W x H 530 x 500 x 965 mm (including guide bracket) Weight 39 kg defrosting automatic hot gas automatic dehumidification hygrostat-controlled fan axial, 1-stage fan automatic shutdown when bucket is full Yes prefilter Yes timer no (operation with timer possible) continuous operation possible Yes memory function yes (saves set values ​​mechanically) hose connection yes (no hose included) pump optionally available (not included) guarantee 2 years

Read more less

A very powerful construction dryer with brute dehumidification power. Perfect for drying large construction sites and for effectively drying out water damage. This dehumidifier has consistently omitted everything that is unnecessary for continuous use. It has neither a display nor a hygrostat (a plug-in hygrostat can be ordered optionally if required). This makes it very easy to use, safe from tampering and extremely affordable for this performance class. On the other hand, everything you need for fast drying is there: powerful dehumidification performance, hot gas defrosting, hour counter as well as large rollers and a guide bar for easy mobility on construction and damage sites.     Easy operation   It's very easy to set up. Set it up - connect the hose - plug it in - turn the main switch - done!   The operation will now continue until the dryer is uninstalled again. As long as the device is connected to the power supply, it will run reliably and there are no settings that can be changed or manipulated by mistake. This also applies in the event of a power failure: when the power comes back on, the dehumidifier will continue its task with the same settings.   Thanks to the professional hot gas automation, it can also be used in cooler environments without any problems, although the dehumidification power decreases at cold temperatures, as with all condensation dryers. The built-in finned evaporator (cooling element) has an extremely high efficiency in temperate environments and can dry the air to just under 40% RH. The dryer is also equipped with a rotary piston compressor. This means that it can be transported and stored in any position.     Optional hygrostat   Should a hygrostat be required at some point to regulate the target humidity, the dryer is prepared so that the Trotec hygrostat HG110 can be connected directly using a jack plug. Please note the accessories.     Direct hose connection   With dryers of this strength, collecting water in an integrated bucket makes little sense, as this would constantly fill up. The water extracted from the air is therefore drained away via a directly connected hose. The hose must be laid in a downward direction, as there is no pump integrated into the dryer. Free-standing condensate pumps are optionally available if the water needs to be pumped up or out.     Suitable for unattended continuous operation   This "TTK" is suitable for longer, unattended drying operations. The exact operating time can be determined precisely using the hour counter that is integrated as standard. This is particularly useful for commercial applications. Thanks to the counter, it is also possible to determine whether the device was always in operation or whether it was switched off accidentally or intentionally.     Hydrofluoroolefin (R-454C) as an environmentally friendly refrigerant in dehumidifiers   Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using hydrofluoroolefin (R-454C) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection.   The natural refrigerant hydrofluoroolefin (R-454C) is an organic compound and is classified as a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly hydrofluoroolefin (R-454C) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=146).   Additional benefit for the environment: Due to its excellent thermodynamic properties, hydrofluoroolefin (R-454C) is a particularly energy-efficient refrigerant and thus also reduces your energy costs.   Advantages at a glance   • Affordable price with strong performance in the commercial sector • Can also be used in cooler environments thanks to hot gas defrosting • Robust steel construction with large rollers and guide bar • Suitable for continuous operation • Can be transported and stored in any position thanks to the rotary piston compressor • External hygrostat connection     Technical data   dehumidification performance at 30 °C / 80 % RH 100 liters / day air volume 1000 m³/h Maximum room size 250 m² (750 m³) Minimum room size 8 m² (30 m³) temperature range 5 - 32°C humidity range technically humidity range practice 30 - 90 % RH 40 - 90% RH (finned evaporator) voltage 220 - 240 V/50 Hz nominal current consumption max. 8.1 A power consumption max. 1920W Recommended coverage 16 A cable length approx. 2 m Plug EU plug with Swiss adapter refrigerant R454C (1000g) GWP146 water bucket no bucket operating noise 67 dB(A) at 1 m distance 64 dB(A) at 2.5 m distance Dimensions D x W x H 538 x 698 x 1006 mm including guide bar and rollers Weight 64 kg defrosting automatic hot gas automatic dehumidification Continuous operation, a plug-in mechanical hygrostat is available as an option. fan radial, 1-stage fan prefilter Yes operating hour meter Yes continuous operation possible Yes display no memory function yes (saves set values ​​automatically) hose connection yes, not included in delivery (suitable inner diameter: 12mm) guarantee 2 years

Read more less

The new AD 520 was specially developed for professional use. The extra-lightweight housings are particularly popular on construction sites and when drying out water damage. Thanks to the latest technology, they are economical and can be used in temperatures down to just below freezing. The water is collected in a 7-litre condensate tank as standard, with a float automatically stopping operation when the tank is full. The water can also be drained directly via the hose connection. The condensate hose can be plugged directly onto the water nozzle without a coupling (we recommend a clamp for secure attachment). Optional pump kit: A suitable plug-in, fully integrated pump kit is available as an additional option, which can be used to transport the condensate to higher elevations or over greater distances. The pump kit can be easily removed at any time and replaced with a bucket. The built-in operating hour counter shows clearly and quickly how long the device has been in use. The consumption meter provides information about the power consumption in kWh.  Characteristics • Housing: Sheet steel coated in stainless steel look • Installation: Four abrasion-resistant rubber feet for floor installation • Air flow: Air inlet rear / Air outlet front • Carrying handle: Sturdy foldable handle for carrying • Wall mounting: Wall bracket optionally available • Stackable: for transport and storage • Air filter: Protects the device from dust • Fan: 2-stage, energy-efficient EC fan • Condensate drain: Water tank 7 liters with automatic shutdown when full and when drained, hose connection • Pump kit: Flexible pump kit for permanent condensate drainage (accessory) • Blue-Dry technology: For particularly energy-saving operation – even at low humidity and temperatures • Memory function: After a power failure, it resumes operation with the same settings. Therefore, it is also suitable for operation with a timer, for example. • Hot gas defrosting: Can also be used in cooler environments thanks to automatic self-defrosting. • Suitable for unattended continuous operation It is suitable: • as a construction dryer • for dehumidification of basements, commercial premises, industry up to 60m² and in case of water damage • for unattended continuous operation • for operation with a timer The manufacturer "Aerial" belongs to the Dantherm Group and is one of the leading European producers of high-quality professional construction dryers and dehumidifiers for commercial and private use. This dryer is also available in the larger version AD540 . Aerial "eDRY®" for efficient air dehumidification The prerequisite for economical operation and reduced energy consumption is the optimal coordination of the components and the use of advanced measurement and control technology. With the development of "eDRY", Aerial was able to further improve the user-friendliness and energy efficiency of the AD series. The use of digital precision sensors in conjunction with the eDRY electronics enables very precise measurement and control of the room humidity. dehumidification performance Thanks to sophisticated hot gas defrosting, the dryer can be used over a wide temperature range between +3°C and +34°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: 30°C / 80% RH: 19 liters / 24h (power consumption: 330 W) 27°C / 60% RH: 11 liters / 24h (power consumption: 295 W) 20°C / 60% RH: 8 liters / 24h (power consumption: 260 W) 10°C / 70% RH: 6 liters / 24h (power consumption: 210 W) (RH=relative humidity)   latest technology Thanks to the latest technology, it is highly efficient and economical. The R1234yf refrigerant it contains has hardly any impact on the environment. The "Global Warming Potential (GWP)" is an incredible value of 4, which corresponds to a reduction of 99.5% compared to comparable models of previous generations.    Technical data  Tension: 220-240V / 50Hz Power consumption: max. 330W (1.4A) / 260W (at 20°C/60% RH) Sound pressure level: 1 m distance: 49 dB(A) 2.5 m distance: 46 dB(A) Dehumidification performance: max. 19 liters/day (30°C / 80% RH) air circulation volume: 2-stage 250 / 340 m³/h water bucket: 7 liter capacity, matching pump kit optionally available. Compressor: rotary compressor refrigerant: R1234yf Dimensions (H x W x D): 524 x 320 x 360 mm Weight: 17 kg Operating setting: Digital control panel Ambient temperature: Ambient humidity: 3°C ~ 34°C 30 - 95% RH Application area: up to 60m² (or 150 m³) Swiss plug: Yes hose connection: Yes Operating hour meter: Yes Consumption meter kWh: Yes Guarantee: 2 years

Read more less

Hard worker among construction dryers! Whether drying out after water damage, drying new buildings or keeping heated and unheated storage rooms dry - the 650S is a universally applicable dehumidifier with high-quality workmanship and reliable operation. It is manufactured in a specialized factory in Europe. It is built to last, easy to care for, rarely needs maintenance and is very affordable considering its power and quality .     Easy operation   The desired target humidity can be continuously regulated between 32 - 100% using a mechanical hygrostat; continuous operation is also possible. The high air circulation volume of an impressive 925 cubic meters per hour is particularly useful in larger zones. With its stable carriage construction and large wheels, frequent changes of location can be carried out very easily.     Direct hose connection and optional pump kit   Due to its very high dehumidification capacity, this dehumidifier has a direct connection for condensate drainage instead of a water tank. The hose must have a gradient towards the drain. If this is not possible, a suitable pump kit is optionally available, with which the water can be pumped up and away.   The operating switch is protected against dust and splash water by a protective cap and a slotted hygrostat rotary switch protects against accidental adjustment of the switch position.     Professional hot gas defrosting   Inside, a professional hot gas automatic defrosting system ensures effective dehumidification results. The finned evaporators are particularly effective in temperatures above 10°C and in humidity levels above 40%. Technically, the dryer can be used at room temperatures down to around 5°C, even in unattended continuous operation.     Optional counters   The delivery does not include an hour or consumption meter. You can order these from us if you wish (the housing is prepared for retrofitting as standard). You can choose between a pure hour meter or the combined dual meter, which measures hours and power consumption. The meters are MID-compliant. Outside Switzerland, dryers used professionally must already be MID-compliant.     Hydrofluoroolefin (R-454C) as an environmentally friendly refrigerant   Every year, synthetic refrigerants release several million tons of environmentally harmful CO2 emissions (greenhouse gases) into the air. Therefore, the use of alternative refrigerants is one of our most important goals. By using hydrofluoroolefin (R-454C) as a refrigerant, this dehumidifier makes a valuable contribution to climate protection. The natural refrigerant hydrofluoroolefin (R-454C) is an organic compound and is classified as a hydrocarbon. In contrast to synthetic refrigerants, environmentally friendly hydrofluoroolefin (R-454C) has neither ozone depletion potential (ODP=0) nor a significant greenhouse effect (GWP=146).     Advantages at a glance   • High dehumidification performance even at low temperatures • Robust plastic-coated metal housing • Can be transported and stored in any position thanks to the rotary piston compressor • Stable carriage construction • Automatic hygrostat-controlled dehumidification operation • Quality hot gas automatic defrosting • Possibility of retrofitting MID-compliant dual meters for operating hours and kilowatt hours (optional) • Possibility to add a suitable pump kit, which can be connected directly to the device (optional)     Technical data   dehumidification performance at 30 °C / 80 % RH 91 liters / day air volume 925 m³/h Maximum room size 230 m² (550 m³) Minimum room size 4 m² temperature range 5 - 32°C humidity range technically humidity range practice 32 - 90 % RH 40 - 90 % RH voltage 220 - 240 V/50 Hz nominal current consumption max. 9.5 A power consumption max. 2100 W Recommended coverage 16 A cable length approx. 3 m Plug EU plug with Swiss fixed adapter refrigerant R-454C (1050g) GWP 146 water bucket no bucket, only hose connection suitable hose: 16 mm inner diameter operating noise 56 dB(A) at 1 m distance 53 dB(A) at 2.5 m distance Dimensions D x W x H 616 x 511 x 1022 mm (including guide bracket) Weight 52 kg defrosting automatic hot gas automatic dehumidification hygrostat-controlled fan axial, 1-stage fan prefilter Yes timer no (operation with timer possible) continuous operation possible Yes memory function yes (saves set values ​​mechanically) hose connection yes (no hose included) - 16 mm pump optionally available (not included) guarantee 2 years

Read more less

Very powerful dehumidifier for demanding dehumidification tasks in a temperate environment. Ideal for drying water damage, for building drying for larger or very humid rooms. Due to its high performance, this dryer is only available with a hose connection, i.e. without a water tank. The device is also ideal for construction sites and for drying wood.   Dehumidification capacity of up to 100 liters per day Overview of the approximate dehumidification quantities in liters per day at different room temperatures and humidity: 30°C: 80% moist: 100 liters (60%: 47 L.) 20°C: 80% moist: 47 liters (60%: 27 L.) 15°C: 80% moisture: 35 liters (60%: 19 L.) 10°C: 80% moisture: 19 liters (60%: 13 L.) Quality product, which is mostly sold through specialist retailers throughout Europe. Quality standards include: durability, compliance with the specified performance, CFC-free, TÜV + GS + EMC + CE tested, ISO certified, recyclable materials, etc. Devices with comparable performance usually cost several times more. Characteristics • Dehumidification capacity of up to 120 liters per day • Electric hygrostat (LED) for regulating and setting the desired humidity • Function for continuous operation/continuous dehumidification; • Memory function for saving data and for automatic continuation of operation after a power failure • Clear display including actual humidity, target humidity and status overview • separate consumption meter kWh • Equipped with a highly efficient rotary compressor. This TÜV and CE tested compressor is one of the most powerful compressors on the market • Automatic professional defrost function • Humidity control of seamless 1% steps between 30% - 90% (plus continuous operation function) • Powder-coated metal housing/metal frame • Very easy mobility thanks to transport handles and large wheels for safe travel over steps and uneven ground. However, note the weight (60kg). • Operating warning light / defrost light • Maintenance-free / No separate or renewed coolant is required (closed circuit) • Air filter grille that can be cleaned • The device is ready for use immediately (no installation or assembly required). • Swiss plug 230 V • CFC free and compliance with WEEE standards usage examples Construction dryer: Ideal for quickly drying concrete, basements, plaster, screed, water damage, etc. Damage repair: After flooding or damage caused by extinguishing water, these devices are ideal for drying (professionals as well as insurance companies use these devices.) Climate control: For all rooms, halls as well as for use at work and for hobbies, etc. Important The powerful compressor operates at a noise level of around 70 dB and is therefore not suitable for use in noise-sensitive areas. The fuses must release 9 amps or more, which is usually the case with a normal socket. At temperatures below 10°C the Akto1200 can freeze. In cold environments we recommend the model Fral F96 -> Construction dryer F96 as an alternative.     Technical data   Tension 220-240V / 50Hz power consumption max. 1840W (8.3 A) / 1560W (7.1 A) (at 20°C/60% RH) sound pressure level 1 m distance 70 dB(A) 2.5m distance 67 dB(A) (our measurement) dehumidification performance 100 liters/day (30°C / 80% RH) amount of recirculated air 1000 m³/h (free blowing) condensate tank No tank / only hose connection possible compressor rotary compressor refrigerant R454C (1kg), GWP: 148 Dimensions (H x W x D) 1110 x 630 x 470 mm Weight 60 kg cessation of operations predefined values ​​at the touch of a button / digital display ambient temperature 10°C ~ 32°C (our recommendation) application area Rooms from min. 4m² to max. 300m² (750m³) Swiss plug Yes hose connection Yes operating hour meter Yes guarantee 2 years series WDH-1200HT

Read more less

The AD540 construction dryers from Aerial were specially developed for professional use. The extra-lightweight housings are particularly popular on construction sites and for drying water damage. Thanks to the latest technology, they are economical and can be used in temperature ranges down to 3°C. The water is collected in a 7-litre condensate tank as standard, with a float automatically stopping operation when the tank is full. The water can also be drained directly via the hose connection. The matching condensate hose has an inner diameter of 12mm = 1/2 inch and can be plugged directly onto the water nozzle without a coupling (we recommend a clamp for secure fastening). Optional pump kit: A suitable plug-in, fully integrated pump kit is available as an additional option, which can be used to transport the condensate to higher elevations or over greater distances. The pump kit can be easily removed at any time and replaced with a bucket. The built-in operating hour counter shows clearly and quickly how long the device has been in use. Two-stage blower with 500 or 625 m³ of circulating air per hour. AD540 Features • Housing: Sheet steel coated in stainless steel look • Installation: Four abrasion-resistant rubber feet for floor installation • Air flow: Air inlet rear / Air outlet front • Carrying handle: Sturdy foldable handle for carrying • Wall mounting: Wall bracket optionally available • Stackable: for transport and storage • Air filter: Protects the device from dust • Fan: 2-stage, energy-efficient EC fan • Condensate drain: Water tank 7 liters with automatic shutdown when full and when drained, hose connection • Pump kit: Flexible pump kit for permanent condensate drainage (accessory) • Blue-Dry technology: For particularly energy-saving operation – even at low humidity and temperatures • Memory function: After a power failure, it resumes operation with the same settings. Therefore, it is also suitable for operation with a timer, for example. • Hot gas defrosting: Can also be used in cooler environments thanks to automatic self-defrosting. • Suitable for unattended continuous operation The AD540 is suitable: • as a construction dryer • for dehumidification of basements, commercial premises, industry up to 90m² and in case of water damage • for unattended continuous operation • for operation with a timer The manufacturer "Aerial" belongs to the Dantherm Group and is one of the leading European producers of high-quality professional construction dryers and dehumidifiers for commercial and private use. This dryer is also available in the smaller version AD520 . Aerial "eDRY®" for efficient air dehumidification The prerequisite for economical operation and reduced energy consumption is the optimal coordination of the components and the use of advanced measurement and control technology. With the development of "eDRY", Aerial was able to further improve the user-friendliness and energy efficiency of the AD series. The use of digital precision sensors in conjunction with the eDRY electronics enables very precise measurement and control of the room humidity.     dehumidification performance Thanks to sophisticated hot gas defrosting, the dryer can be used over a wide temperature range between +3°C and +34°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: 30°C / 80% rF = 34.0 liters / 24h (power consumption: 530 W) 27°C / 60% rF = 22.0 liters / 24h (power consumption: 430 W) 20°C / 60% rF = 16.6 liters / 24h (power consumption: 390 W) 10°C / 70% rF = 11.4 liters / 24h (power consumption: 330 W) (RH=relative humidity) Technical data  Tension: 220-240V / 50Hz Power consumption: max. 540W (2.3A) / 390W (at 20°C/60% RH) Sound pressure level: 1 m distance: 51 dB(A) 2.5 m distance: 54 dB(A) Dehumidification performance: max. 34 liters/day (30°C / 80% RH) air circulation volume: 2-stage 500 / 625 m³/h water bucket: 7 liter capacity, matching pump kit optionally available. Compressor: rotary compressor refrigerant: R454c GWP146 Dimensions (H x W x D): 578 x 329 x 380 mm Weight: 24 kg Operating setting: Digital control panel Ambient temperature: Ambient humidity: 3°C ~ 34°C 30 - 95% RH Application area: up to 60m² (or 150 m³) Swiss plug: Yes hose connection: Yes Operating hour meter: Yes Consumption meter kWh: Yes Guarantee: 2 years

Read more less

The AD40 is versatile and so light that it can be carried like a suitcase. Thanks to BlueDry® technology, the AD40 dehumidifies consistently and reliably even at low humidity and temperatures. service It is easy to operate using the innovative eDRY® electronics. All controls are clearly arranged and all important operating states can be called up at any time. The target and actual humidity are shown on the display. Operating hours (consumption) can be easily read. Energy consumption is shown using the additional, calibrated energy meter. The control system is equipped with a memory function. This means that in the event of a power failure, e.g. on construction sites, operation will resume with the same settings as soon as the power is restored. water bucket or optional pump The water collection container (6.8 liters) is easy to remove, carry and empty. It is located inside, and the fill level of the water bucket is measured by a float. When it is full, this automatically stops operation, and operation also starts again automatically when the bucket is put back in. A suitable pump kit is optionally available, which can be used flexibly and is also suitable for unattended continuous operation. Robust housing The housing is easy to clean and easy to dismantle for any service work that may be required. It has a fold-up handle. Lashing straps can be attached to each side. The protected socket is used to connect additional devices. Four robust, stable plastic feet for floor installation. Can be stacked with other Aerial Aercube devices. Characteristics  • Housing: made of robust, impact-resistant and UV-resistant plastic, lightweight. Fixing points for AERCUBE® lashing system. • Cable: integrated cable winding. • Installation: freestanding or mounted on Aercube system (fixing points for AERCUBE lashing system). • Air flow: transverse, side intake and outlet. • Air filter: Protects the device from dust. • Fan: 2-speed, energy efficient EC fan. • Defrost: Demand-controlled hot gas defrosting. • Condensate pump: Optional pump kit available. • Blue-Dry technology: For particularly energy-saving operation – even at low humidity and temperatures. • Calibrated energy meter (MID compliant). • Memory function: After a power failure, it resumes operation with the same settings. Therefore, it is also suitable for operation with a timer, for example. • Hot gas defrosting: Can also be used in cooler environments thanks to automatic self-defrosting. • Suitable for unattended continuous operation. • Own design: available in all colours and with your logo for larger quantities. All AERCUBE system components are 100% compatible with each other and stackable. Aerial "eDRY®" for efficient air dehumidification The prerequisite for economical operation and reduced energy consumption is the optimal coordination of the components and the use of advanced measurement and control technology. With the development of "eDRY", Aerial was able to further improve the user-friendliness and energy efficiency of the AD series. The use of digital precision sensors in conjunction with the eDRY electronics enables very precise measurement and control of the room humidity.    dehumidification performance Thanks to sophisticated hot gas defrosting, the dryer can be used over a wide temperature range between +1°C and +34°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: 30°C / 80% rF = 35.0 liters / 24h (power consumption: 520W) 27°C / 60% rF = 22.0 liters / 24h (power consumption: 430W) 20°C / 60% rF = 15.0 liters / 24h (power consumption: 370W) 10°C / 70% rF = 8.0 liters / 24h (power consumption: 300W) (RH=relative humidity)     Technical data   Tension: 230V / 50Hz Power consumption: max. 530W Sound pressure level: 1 m distance 57 dB(A) 2.5 m distance 54 dB(A) 3 m distance 53 dB(A) Dehumidification performance: max. 35.0 liters / day (30°C / 80% RH) Bucket: Capacity 6.8 liters, Operational interruption due to floats Recirculation air volume level 1 / 2: 300 / 400 m³/h refrigerant: R407C Dimensions (H/W/D): 580 / 390 / 450 mm Weight: 25 kg Operating setting: Digital Ambient temperature: +1°C - +34°C Application area: up to approx. 100 m² Swiss plug: Yes hose connection: connection piece for direct hose connection Optional pump kit Operating hour meter: Yes Guarantee: 2 years

Read more less

State-of-the-art drying technology! The 9 series of Aerial construction dryers was developed completely to meet the needs of use on construction sites, in industry and for drying water damage. The dryers have an MID-approved kWh meter and a non-resettable hour meter as standard. Thanks to the CC 6 control, the devices are compatible with the "Simplify" remote monitoring solution, which allows operation to be conveniently monitored remotely. The AD-935 has an 8-litre condensate tank and a connection nozzle for direct drainage of the condensate via a hose. A suitable pump kit is also available, which the device automatically recognises when inserted. The moist room air is sucked in at the front of the housing and the dry air is blown out to the rear. In the intake area, a reusable, industrial filter mat cleans the air and ensures that flying particles do not get into the device.    service   The device is operated via the control panel on the side. With only three buttons, it is comfortable and easy to use. It shows all the important information and the desired values ​​can be set at the touch of a button. • Simple 3-button operation • Color-coded status display of room conditions - red, yellow, green • Fully graphical display, no translation required     High service friendliness   The housing was designed so that it can be opened with little effort. This means that internal components can be cleaned quickly and easily or replaced if necessary.     Features at a glance   • CC 6 control unit compatible with the Simplify remote monitoring solution • OEM versions available on request (minimum order quantity 50) • Use of standardized components from the Dantherm Group product portfolio ensures quick access to spare parts • Integrated interface for accessories (dew point kit and external hygrostat) • Automatic detection of the pump kit • Various drainage options: standard with Ø15mm hose connection, water tank and optional pump set • MID-approved kWh meter and non-resettable hour meter as standard • 2-speed fan • Integrated night mode for quieter operation in occupied rooms • R454C refrigerant, non-toxic and non-flammable, with extremely low GWP (Global Warming Potential) • Large wheels • Telescopic handle • Stackable • Maintenance and service friendly     dehumidification performance The dryer can be used over a temperature range between +5 °C and +30 °C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: 30°C / 80% rF = 34.0 liters / 24h (power consumption: 610 W) 20°C / 60% rF = 16.5 liters / 24h (power consumption: 450 W) (RH=relative humidity)     Technical data  Tension 230V / 50Hz power consumption 610 W max. sound pressure level 2.5 m distance 51 dB(A) dehumidification performance 34 liters/day (30°C / 80% RH) condensate tank Approx. 8 liters air volume level 1 / 2 300 / 420 m³/h (night mode: 300 m³/h) compressor rotary compressor refrigerant R454C Dimensions (H x W x D) 860 x 392 x 508 mm Weight 35.4 kg cessation of operations CC 6 control panel, wireless connection with Simplify remote monitoring possible ambient temperature ambient humidity 5 °C - 30 °C 30% RH - 90% RH Swiss plug Yes, cable length approx. 5 m hose connection 15 mm hose inner diameter guarantee 2 years

Read more less

A powerful dehumidifier for construction sites and industry. The powerful fan ensures a wide-area exchange of moist and dry air. It has a housing made of impact-resistant plastic, two large wheels and a fold-up handle for easy movement around the floor and even over stairs.   The moist air is drawn in at the back via an easily removable air filter. The dry air is blown out at the front through slanted slats. Characteristics • Fan: Axial fan with aluminum impeller. Motor with winding protection. • Compressor: Fully hermetic rotary piston compressor, protected against overload, vibration-damped mounting. • Condenser/evaporator: made of copper tubes with attached aluminum fins • Self-defrosting: automatic hot gas defrosting controlled by DryLogic, therefore usable down to freezing point • Collection container: 6.8 liters with automatic full level shut-off • Hose connection: nozzle (15 mm) for direct condensate drainage. Pump available as an option. • Hygrostat: digital with hygrostat rotary knob • Operating hour counter • Consumption meter kWh: calibrated, can be read without power • 2 large transport wheels: for easy mobility on construction and damage sites • Memory function: After a power failure, it resumes operation with the same settings. Therefore, it is also suitable for operation with a timer, for example. • Suitable for unattended continuous operation. Aerial "eDRY®" for efficient air dehumidification The prerequisite for economical operation and reduced energy consumption is the optimal coordination of the components and the use of advanced measurement and control technology. With the development of "eDRY", Aerial was able to further improve the user-friendliness and energy efficiency of the AD series. The use of digital precision sensors in conjunction with the eDRY electronics enables very precise measurement and control of the room humidity.    dehumidification performance Thanks to sophisticated hot gas defrosting, the dryer can be used over a wide temperature range between +1°C and +34°C, although as with all condensation dryers, the dehumidification power decreases in cooler environments. Examples of dehumidification performance and consumption under different (constant) ambient conditions: at 30°C / 80% RH = 37.0 liters / day (power consumption: 520 W) at 27°C / 60 %RH = 23.0 liters / day (power consumption: 430 W) at 20°C / 60% RH = 16.5 liters / day (power consumption: 390 W) at 10°C / 70% RH = 8.0 liters / day (power consumption: 320 W)   Technical data   Tension: 230V / 50Hz Power consumption: max. 520 W (10A) / 390W (at 20°C/60% RH) Sound pressure level: 2.5 m distance 51 dB(A) (manufacturer information) Dehumidification performance: max. 37 liters/day (30°C / 80% RH) Recirculation air volume level 1/2: 450 / 550 m³/h condensate tank: approx. 6.8 liters Compressor: rotary compressor refrigerant: R407c (550gr.) Dimensions (H / W / D): 690 x 390 x 470 mm Weight: 32 kg Operating setting: Digital control panel Ambient temperature: 1°C ~ 34°C (35 - 99% RH) Application area: up to 100m² / 300m³ Swiss plug: Yes hose connection: Yes Operating hour meter: Yes Guarantee: 2 years

Read more less