The MK 8 measuring cable is an accessory for Gann resistance-based measuring devices. It connects the base device with the associated measuring electrodes such as M6 and others. Matching electrode pairs • Flat electrode pair M 6-Bi 200 and M 6-Bi 300 • Insertable electrode tip pair M 20-Bi 200 and M 20-Bi 300 • Insertable electrode tip pair M 6-150 and M 6-250  Suitable base devices • Hydromette BL E, BL H 40, BL H 41, BL HT 70, H 35, HB 30, HT 65, HT 85 T, M 2050, M 4050, RTU 600, UNI 2  The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.  Technical data  Gann Article No.: 31003750 Length: 1 m

Read more less

The M 20 is a drive-in electrode for measuring wood moisture and building moisture. It is based on the resistance measuring principle and can be connected to all corresponding "Gann" measuring devices. The electrode is suitable for moisture measurements in sawn timber (up to 50 mm thick), chipboard and OSB boards and parquet. Using a suitable impact device (eg hammer), the electrode can also be driven into hard woods such as beech. It can also be used for measurements in soft, set building materials (eg plaster, gypsum or aerated concrete) as well as insulation and insulating materials. Matching electrode pairs • M20-HW200, M20-HW300 • M20-DS16, M20-DS16-i, M20-OF15 • M20-Bi 200 and M20-Bi 300 • M6-150 and M6-250 Suitable base devices • Hydromette BL E • Hydromette HB 30 • HT 85 T • M 4050 • RTU 600 • UNI 2     The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.  Technical data Gann Article No.: 31003300 Electrode M20 including 10 electrode tips of 16 and 23 mm 

Read more less

Ideal case for storing and transporting Gann measuring instruments such as Hydromettes and Hydromat CM devices. With specific inlays and padding. For storage / transport of GANN Hydromettes + accessories with specific inlays and padding. • For all Classic or BL Hydromettes • Designed for a measuring sensor and various resistance-based electrodes   The manufacturer Gann from Germany is one of the leading producers of high-quality moisture measuring devices. Gann measuring devices are very often used by professionals in building drying. An ideal companion on construction sites for site managers, architects and floor fitters.     scope of delivery The delivery includes the padded but empty case without devices.    Technical data  Gann Article No.: 31005061 Length: 0.437 m Width: 0.379 m Height: 0.100 m Weight: 1,530 kg

Read more less

The M6 ​​plug-in electrodes are accessories for Gann professional measuring devices such as Uni2 and all hydromets that are based on the resistance measurement method. The electrodes are always used in pairs. They measure the resistance between the two plug-in tips, which are ideally inserted into the material being measured at a distance of approx. 8 - 10 cm from each other. The M6 ​​is suitable for measuring hard, set building materials (e.g. concrete or screed). To use it, you need a basic measuring device such as Uni1 or Uni2 and a measuring cable MK8. ​​The delivery includes 10 electrode tips each of 40 and 60 mm in length. The M6 ​​also serves as a carrier for other electrode pairs: Matching electrode pairs • Flat electrode pair M 6-Bi 200 and M 6-Bi 300 • Insertable electrode tip pair M 20-Bi 200 and M 20-Bi 300 • Insertable electrode tip pair M 6-150 and M 6-250 Suitable base devices • Hydromette BL E, Hydromette HB 30, HT 85 T, M 4050, RTU 600, UNI 2 The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.  Technical data Gann Article No.: 31003700 2 carrying handles, including 10 electrode tips of 40 and 60 mm

Read more less

Ideal case for storing and transporting Gann measuring instruments such as Hydromettes and Hydromat CM devices. With specific inlays and padding. The delivery includes the padded but empty case without devices. • For all Classic or BL Hydromettes • Designed for up to three measuring sensors and various resistance-based electrodes The manufacturer Gann from Germany is one of the leading producers of high-quality moisture measuring devices. Gann measuring devices are very often used by professionals in building drying. An ideal companion on construction sites for site managers, architects and floor fitters.  Technical data  Gann Article No.: 31005062 Length: 0.497 m Width: 0.411 m Height: 0.120 m Weight: 1,910 kg

Read more less

The plug-in electrode tips M6-150 and M6-250 are accessories for Gann professional measuring devices such as the Uni2 and others. The probes are uninsulated and extra thin with a diameter of just 3 mm. They are therefore suitable for measuring moisture in building and insulation materials via floating joints or through a joint cross. The electrode pair is uninsulated. Available in two lengths, approximately 150 mm (M6-150) or 250 mm (M6-250) long. To use the electrode tips, either an M 6 electrode and / or an M 20 electrode are required The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies. Suitable base devices • CH17 • BL E • HB 30 • HT 85 T • UNI 2 • RTU 600  Technical data  M6-150 (Gann article no.: 31003706): 150 x 3 mm Ø M6-250 (Gann article no. 31003707): 250 x 2 mm Ø

Read more less

The plug-in electrode tips M6-150 and M6-250 are accessories for Gann professional measuring devices such as the Uni2 and others. The probes are uninsulated and extra thin with a diameter of just 3 mm. They are therefore suitable for measuring moisture in building and insulation materials via floating joints or through a joint cross. The electrode pair is uninsulated. Available in two lengths, approximately 150 mm (M6-150) or 250 mm (M6-250) long. To use the electrode tips, either an M 6 electrode and / or an M 20 electrode are required The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies. Suitable base devices • CH17 • BL E • HB 30 • HT 85 T • UNI 2 • RTU 600  Technical data  M6-150 (Gann article no.: 31003706): 150 x 3 mm Ø M6-250 (Gann article no. 31003707): 250 x 2 mm Ø

Read more less

The plug-in electrode tips M 20-Bi 200 and M 20-Bi300 are accessories for Gann professional measuring devices such as the Uni2 and others. They are made of V2A and are designed for depth measurements in old buildings, wooden beams (e.g. in roofs) and soft, set building materials. The electrode pair is insulated at the shaft and is approximately 200 mm (M20-Bi200) or 300 mm (M30-Bi300) long. To use the electrode tips, either a plug-in electrode pair M6 and/or an impact electrode M 20 are required. Suitable base devices The electrode tips can be used with all hydromets that are based on the resistance measurement method: • CH17 • BL E • HB 30 • HT 85 T • UNI2 • RTU 600  The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.   Technical data M20-Bi 200 (Gann article no. 31004360): 200 mm [L] x 4 mm [Ø] M20-Bi300 (Gann article no. 31004365): 300 mm [L] x 4 mm [Ø] 2-year warranty

Read more less

The flat electrodes M 6-Bi 200 and M 6-Bi300 are accessories for Gann professional measuring devices such as the Uni2 and others. They are suitable for measuring moisture in edge and floating joints. For example, when water needs to be detected that is located under the subfloor. The electrodes are insulated at the shaft so as not to influence the measurement result. The electrode pair is insulated at the shaft and they are approximately 200 mm (M6-Bi200) or 300 mm (M6-Bi300) long. A pair of M6 electrodes is required to support the flat electrodes The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.  Technical data  Dimensions M6-Bi200 (Gann article no. 31003702): 200 x 10 x 0.8 mm Dimensions M6-Bi300 (Gann article no. 31003703): 300 x 10 x 0.8 mm

Read more less

The plug-in electrode tips M 20-Bi 200 and M 20-Bi300 are accessories for Gann professional measuring devices such as the Uni2 and others. They are made of V2A and are designed for depth measurements in old buildings, wooden beams (e.g. in roofs) and soft, set building materials. The electrode pair is insulated at the shaft and is approximately 200 mm (M20-Bi200) or 300 mm (M30-Bi300) long. To use the electrode tips, either a plug-in electrode pair M6 and/or an impact electrode M 20 are required. Suitable base devices The electrode tips can be used with all hydromets that are based on the resistance measurement method: • CH17 • BL E • HB 30 • HT 85 T • UNI2 • RTU 600  The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.   Technical data M20-Bi 200 (Gann article no. 31004360): 200 mm [L] x 4 mm [Ø] M20-Bi300 (Gann article no. 31004365): 300 mm [L] x 4 mm [Ø] 2-year warranty

Read more less

The flat electrodes M 6-Bi 200 and M 6-Bi300 are accessories for Gann professional measuring devices such as the Uni2 and others. They are suitable for measuring moisture in edge and floating joints. For example, when water needs to be detected that is located under the subfloor. The electrodes are insulated at the shaft so as not to influence the measurement result. The electrode pair is insulated at the shaft and they are approximately 200 mm (M6-Bi200) or 300 mm (M6-Bi300) long. A pair of M6 electrodes is required to support the flat electrodes The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.  Technical data  Dimensions M6-Bi200 (Gann article no. 31003702): 200 x 10 x 0.8 mm Dimensions M6-Bi300 (Gann article no. 31003703): 300 x 10 x 0.8 mm

Read more less

The UNI 1 is an electronic and universal triple measuring device to which a wide range of active electrodes can be connected. The measuring ranges building moisture, air humidity and temperature can be measured. Measurements cannot be taken with the UNI1 alone. The desired active electrodes (sensors) are also required, which are connected to the measuring device. The following active electrodes can be connected:   • B 50, B 60 and LB 70 for non-destructive moisture measurement and indication in ceilings, walls, floors and other building materials • MB 35 for surface moisture measurement on concrete • MH 34 for measuring high moisture levels (40–200%) in softwood • IR 40 EL for measuring surface temperature, thermal bridges and dew point temperature • RF-T 28, RH-T 37 EL and RH-T 37 EL flex for humidity and air temperature measurement and • all Pt 100 temperature sensors We usually have the B50 and B60 as well as the RF-T 28, RH-T 37 flex in stock, but we can also order any other electrode for you at advantageous prices. The delivery time is approximately 14 days from the order. Using the device and evaluating the data requires some knowledge of moisture measurement. The device is therefore particularly suitable for air conditioning technicians, water damage assessors, insurance companies and as a supplement to a wood moisture meter. If you are looking for a moisture meter that is easier to use, take a look at our handheld measuring devices, which are also available with good precision and at a significantly lower price. Characteristics • Handy quick moisture meter for lightning-fast individual and series measurements • Direct display of humidity values ​​via the large LCD display, resolution: 0.1 digit • Fast measurement of moisture in hardened building materials using the capacitive high-frequency measuring method • Precision in temperature measurement through Pt 100 measuring resistors in 4-wire technology • Fully automatic device comparison scope of delivery The delivery includes the Uni1 base station without any additional accessories. The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.  Technical data  Gann Article No.: 30001430 Device comparison: Fully automatic Single or series measurements: in a matter of seconds Power supply: 9-V block battery (included or Ni-Cd battery (optional accessory) Dimensions (L/W/H): 140 x 90 x 42/50 mm Weight: 230 gr. Guarantee: 2 years

Read more less

Current production bottleneck at the manufacturer. Only small quantities available. An easy-to-use measuring device for detecting moisture in walls, ceilings and floors using a non-destructive measuring method based on the dielectric constant/high frequency measuring principle. It has a digital LCD display and a flexible ball probe for detecting moisture and moisture distribution in solid building materials. Depending on the density of the substance to be measured, the Compact B measures approx. 3 cm into the material. A practical companion on building sites for site managers, architects and floor fitters as a preliminary test device for all CM devices. Due to its ease of use, it is also suitable for private users who want to monitor the drying progress of new buildings or after water damage. Drying can be monitored very easily, especially when walls have soaked up water from below. materials The moisture meter is particularly suitable for solid substances such as concrete, brick and the like. The value for soft materials requires some experience and knowledge of the specific material densities (Sagex, wood, gypsum, etc.). For this application, consider the Gann Hydromette BL Compact B2 model, where the material types can already be preset. The measurement also does not produce good results if the measurement is taken through paving slabs, cavities or protective films. Application The ball probe is held directly onto the material at a right angle. At the push of a button, the moisture content appears in the form of a numerical value within seconds. This can be converted into the moisture value using the table provided. No separate electrodes or cables required. The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.  Technical data   Gann Article No.: 30002030 Measuring range: 0 - 100 digits measuring depth: max. approx. 6 cm Enlargement: 6-fold Device comparison: Fully automatic Single or series measurements: in a matter of seconds Power supply: 9-V block battery (included) Dimensions (H/W/D): 20 x 3.5 x 3.5 cm Weight: 190 gr. Guarantee: 2 years                                Other Gann measuring instruments We are an official sales point for Gann measuring instruments in Switzerland and can offer you all Gann articles at advantageous conditions, for example: Gann Hydromette HB30, HT65, HT85 T, UNI1, UNI2, RTU600, CH17 and many more.

Read more less

The active electrode RFT 28 EL is a sensor for measuring air humidity and air temperature with a fast measuring speed. It is an addition to one of the Gann Hydromette base stations listed below and cannot be operated separately from them. The sensor's fast response speed enables it to detect leaks, such as gaps in doors or leaky windows, as even small air currents affect the measured value display. The sensor adapts to the ambient climate even when switched off. For particularly precise measurements, the device should be exposed to the ambient climate to be measured for 10 - 15 minutes so that any temperature differences between the electrode and the surrounding climate can be compensated.    Suitable base devices  The electrode can be used with all hydromets that support this procedure, i.e. with the following basic devices: • Hydromette M 4050 • Hydromette RTU 600 • Hydromette UNI 1 • Hydromette UNI 2   The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.   Technical data  Gann Article No.: 31003155 Humidity measuring range: 7 - 98 % RH Measuring range air temperature: -10 - +80 °C Humidity measurement tolerance: ± 1.8% (at 10-90% RH) Air temperature measurement tolerance: ± 0.75 °C (-10 to +55 °C) The response time of the humidity sensor (slightly moving air, ambient temperature: 20 - 25 °C) is 20-30 seconds, depending on the humidity difference. Warranty: 2 years

Read more less

The active electrode B 50 is a sensor for measuring building moisture. It works with a capacitive high-frequency measurement and measures all types of solid materials non-destructively. It detects the moisture distribution in ceilings, walls, concrete and other hardened building materials.   The following measuring ranges are covered by the B 50 • 0 - 199 digits (scan range), moisture qualification via table • 0.3 - 8.5 wt.%, conversion depending on the building material via table • 0.3 - 6.5 CM-%, conversion depending on the building material via table Suitable base devices The electrode can be used with all hydromets that support this procedure, i.e. with the following basic devices: • Hydromette HB 30 • Hydromette M 4050 • Hydromette RTU 600 • Hydromette UNI 1 • Hydromette UNI 2    Using the device and evaluating the data requires some knowledge of moisture measurement. The device is therefore particularly suitable for air conditioning technicians, water damage assessors, insurance companies and as a supplement to a wood moisture meter. If you are looking for a moisture meter that is easier to use, consider our handheld measuring devices "Hydromette Compact B" and "Hydromette BL Compact B2", which are also available with good precision and at a significantly lower price. The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.    Technical data   Gann Article No.: 31003750 Depth effect: up to max. 120 mm Measuring range: 0 - 199 digits (scan range), moisture qualification via table 0.3 - 8.5 wt.%, conversion depending on the building material via table 0.3 - 6.5 CM-%, conversion depending on the building material via table Guarantee: 2 years

Read more less

Fast, precise moisture meter for detecting moisture in walls, ceilings and floors. With this easy-to-use, pocket-sized quick moisture indicator, you can quickly and reliably track your drying progress on construction sites or during water damage repair. The electronic moisture indicator works with a non-destructive measuring method based on the dielectric constant/high frequency measuring principle. It has a ball probe for detecting moisture and moisture distribution in solid building materials such as walls, ceilings and floors (only suitable to a limited extent and for indicative purposes for measuring wood). Application First, the desired material is selected via an LCD display and saved at the touch of a button. Then the metal ball is held at a right angle to the material to be measured and the measuring button is briefly pressed. The result is immediately visible.   Handling a ball measuring electrode  It is important to have a 90° angle to the material being measured and to hold the hydrometer/electrode correctly. To avoid any influence from the hand of the person taking the measurement, only the back half of the electrode may be covered by the hand during the measuring and checking process. The front half (display/ball) of the device must remain free.   Correct handling of the device: When taking measurements, always hold the device by the lower part of the housing:     Incorrect handling of the device: During the measurement, the hand influences the measuring field of the ball electrode and thus changes the measured value.    Selectable material table • Display in digits • Cement screed in % by weight • Anhydrite screed in % by weight • Concrete in % by weight • Cement mortar in % by weight • Lime mortar in % by weight • Mixed plaster in % by weight • Gypsum plaster in % by weight • Cement screed in CM % • Anhydrite screed in CM % • Gypsum plaster in CM % • Lime mortar in CM % • Cement mortar in CM % • Mixed plaster in CM % • Concrete in CM % Wt %: The material moisture in weight percent (also solid moisture) indicates the absolute proportion of free water contained in a solid in %. Values ​​in the range of 0.2 - 0.3 % indicate dry materials. CM %: The displayed CM value simulates the removal and measurement of a material sample in the manometer, where the sample is mixed with calcium carbide. This creates a gas whose pressure is measured. Depending on the density of the material, the value is very similar to weight %. For anhydrite, for example, 1 weight % = approx. 1 CM%. For concrete floors, the CM value differs significantly: 1 weight % = approx. 1.5 CM%. Dry concrete floors/walls should have CM values ​​below 2.0% (calcium sulfate or anhydrite screed: below 0.3%). The weight percentage is therefore the easier value to understand for non-specialists. Advantages and Features • Handy pocket-sized moisture meter for quick single and series measurements • A limit value can be set individually for each building material, and if this limit is exceeded, an acoustic warning signal sounds • Scan mode (1 - 199.9 digits) or direct display of moisture values ​​in weight% or CM-% for building materials, resolution: 0.1% • Characteristic curves for 7 types of building materials • Min, max and hold function for the measured values • Automatic calibration when the device is switched on • The device is delivered complete with 9 V battery and plastic box Innovations compared to the previous Hydromette BL Compact B The BL2 is the further development of its predecessor, the Gann Hydromette BL Compact B. • Longer measuring probe for more comfortable use • Significantly stronger high-frequency measuring field for greater penetration depth into the building material • Finer measurement resolution of now 0-199 digits for an even more precise delimitation of wet areas, which was previously only possible with significantly more expensive measuring devices • The direct display of the CM % has been expanded to include several building materials. The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.    Technical data   Gann Article No.: 30012032 Measuring range:  0 – 199.9 digits (scan range) 0.3 – 6.0 wt.% or 0.3 – 4.0 CM-% measuring depth: max. approx. 6 cm Advertisement: device/ambient temperature Trend indicator: hardwood and softwood Max-Hold function: Yes Alarm function: Acoustically Calibration: Automatically Device shutdown: Automatically Single or series measurements: In seconds Power supply: 9-V block battery (included) Dimensions (L x W x H): 190 x 50 x 30 mm Weight: 180 gr. Special features: No separate electrodes or cables required Ideal pre-test device for all CM devices Guarantee: 2 years                                           Other Gann measuring instruments We are an official sales point for Gann measuring instruments in Switzerland and can offer you all Gann articles at advantageous conditions, for example: Gann Hydromette HB30, HT65, HT85 T, UNI1, UNI2, RTU600, CH17 and many more.

Read more less

The active electrode B 60 is a sensor for measuring building moisture. It works with a capacitive high-frequency measurement and measures all types of solid materials non-destructively. It detects the moisture distribution in ceilings, walls, concrete and other hardened building materials. The basic function is the same as the B50 probe, but the B60 also has a built-in limit value adjuster from 20 - 140 digits and an acoustic signal generator.    The following measuring ranges are covered by the B 60 • 0 - 199 digits (scan range), moisture qualification via table • 0.3 - 8.5 wt.%, conversion depending on the building material via table • 0.3 - 6.5 CM-%, conversion depending on the building material via table Suitable base devices  The electrode can be used with all hydromets that support this procedure, i.e. with the following basic devices: • Hydromette HB 30 • Hydromette M 4050 • Hydromette RTU 600 • Hydromette UNI 1 • Hydromette UNI 2    Using the device and evaluating the data requires some knowledge of moisture measurement. The device is therefore particularly suitable for air conditioning technicians, water damage assessors, insurance companies and as a supplement to a wood moisture meter. If you are looking for a moisture meter that is easier to use, take a look at our handheld measuring devices, which are also available with good precision and at a significantly lower price. The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.     Technical data   Gann Article No.: 31003760 Depth effect: up to max. 120 mm Measuring range: 0 - 199 digits (scan range), moisture qualification via table 0.3 - 8.5 wt.%, conversion depending on the building material via table 0.3 - 6.5 CM-%, conversion depending on the building material via table Guarantee: 2 years

Read more less

The UNI 2 is an electronic and universal triple measuring device to which a wide range of active electrodes can be connected, as with the smaller UNI1 model. In addition, all building moisture measuring electrodes that are based on the resistance measuring principle can be connected. The following measuring ranges can be determined. • Building moisture • Humidity • Air temperature • Material temperature • Surface temperature Measurements cannot be taken with the UNI2 alone. The desired active electrodes (sensors) are also required, which are connected to the measuring device. The following active electrodes can be connected: • B 50, B 60 and LB 70 for non-destructive moisture measurement and indication in ceilings, walls, floors and other building materials • MB 35 for surface moisture measurement on concrete • MH 34 for measuring high moisture levels (40–200%) in softwood • IR 40 EL for measuring surface temperature, thermal bridges and dew point temperature • RF-T 28, RH-T 37 EL and RH-T 37 EL flex for humidity and air temperature measurement and • all Pt 100 temperature sensors.   We usually have the B50 and B60 as well as the RF-T 28, RH-T 37 flex in stock, but we can also order any other electrode for you at advantageous prices. The delivery time is approximately 14 days from the order. Using the device and evaluating the data requires some knowledge of moisture measurement. The device is therefore particularly suitable for air conditioning technicians, water damage assessors, insurance companies and as a supplement to a wood moisture meter. If you are looking for a moisture meter that is easier to use, take a look at our handheld measuring devices, which are also available with good precision and at a significantly lower price. measuring ranges   building moisture: for resistance-based measurements: (*) 0 - 80 digits 0.3 - 25 wt.% or 0.3 - 12 CM-%   for capacitive measurements: (*) 0 - 199 digits (scan range) 0.3 - 8.5 wt.% or 0.3 - 6.5 CM-% with B 50, B 60 and LB 70 2 - 8 wt.% with MB 35 on concrete surfaces   when measuring the relative humidity in the borehole: (*) 5 - 98 % RH or 0.2 - 3.7 wt.% with RH-T 37 EL and RH-T 37 EL flex   (wood moisture): 40 - 200 % (atro) with MH 34 on softwood   Humidity: 5 - 98 % RH with RF-T 28, RH-T 37 EL and RH-T 37 EL flex   Temperature: -200 - +600 °C depending on the Pt 100 temperature sensor   Infrared measuring range: -20 - +199.9 °C with IR 40 EL (*) = Moisture conversion in % depending on the building material using the conversion table   Using the device and evaluating the data requires some knowledge of moisture measurement. The device is therefore particularly suitable for air conditioning technicians, water damage assessors, insurance companies and as a supplement to a wood moisture meter. If you are looking for a moisture meter that is easier to use, consider our handheld measuring devices "Hydromette Compact B" and "Hydromette BL Compact B2", which are also available with good precision and at a significantly lower price. Characteristics • Handy quick moisture meter for lightning-fast individual and series measurements • Direct display of humidity values ​​via the large LCD display, resolution: 0.1 digit • Fast measurement of moisture in hardened building materials using the resistance and capacitive high-frequency measuring method • Precision in temperature measurement through Pt 100 measuring resistors in 4-wire technology • Fully automatic device comparison scope of delivery The delivery includes the Uni2 base station without any additional accessories. The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.    Technical data  Gann Article No.: 30001550 Device comparison: Fully automatic Single or series measurements: in a matter of seconds Power supply: 9-V block battery (included or Ni-Cd battery (optional accessory) Dimensions (L/W/H): 140 x 90 x 42/50 mm Weight: 230 gr. Guarantee: 2 years

Read more less

The RHT 37 BL 160 is an electrode for air humidity and air temperature measurements - especially suitable for use in bulk materials and solids (eg masonry or screeds). Its areas of application include moisture analysis, damage assessment, monitoring of building drying and testing the readiness of the floor for laying. and wall coverings. The sensor tube has a diameter of 5.5 mm, which also allows measurements in joints without damaging wall or floor tiles. In conjunction with a hydromette, the air humidity in the borehole can be measured and the readiness for laying or the moisture content of certain hardened building materials can be determined using sorption isotherms . For particularly precise measurements, the device should be exposed to the ambient climate to be measured for 10 - 15 minutes so that any temperature differences between the electrode and the surrounding climate can be compensated. Suitable base devices BL UNI 11 CH17

Read more less

Precise thermo-hygrometer for quick measurements of relative humidity and temperature in cavities Using permanently programmed sorption isotherms, weight or mass percentages can be determined for various building and insulation materials as well as for hard and soft wood. The measuring device has a thin, flexible sensor tube (gooseneck) and is therefore particularly suitable for moisture analyses, e.g. damage assessment or building drying. Testing the readiness for laying floor and wall coverings is also one of the possible areas of application.   Features and Benefits • Handy pocket-sized moisture meter for lightning-fast individual or series measurements • Simultaneous display of up to three measured values ​​via the 3-line LCD display, resolution: 0.1 % or 0.1° C • Automatic calculation of dew point temperature, wood moisture equilibrium (UGL) *, absolute humidity in g/m³, enthalpy in kJ/K, wet bulb temperature in °C and water activity (aw) • Sorption isotherms for hard and soft wood as well as for 10 different types of building materials • Min, max and hold function for the measured values • Storage of the last 5 measured values • Automatic device shutdown     Further versions The Hydromette Compact RH-T Flex is also available with a longer gooseneck (350mm instead of 250mm). The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.    Technical data   Gann Article No.: 31013142 Measuring range: Humidity: 0 – 100 % RH ± 1.8 % RH (10 – 90 % RH) Air temperature: -20 to +70 °C ± 0.5 °C (-10 to +70 °C) sensor tube: 250 x Ø 6.5 mm (gooseneck) Advertisement: device/ambient temperature Automatic saving: last 5 measurements Calibration: Automatically Device shutdown: Automatically Power supply: 9-V block battery (included) Dimensions (L x W x H): 175 x 50 x 30 mm Total length with probe approx. 440mm Weight: 180 gr. Special features: No separate electrodes or cables required 9V block battery included Guarantee: 2 years

Read more less

Precise thermo-hygrometer for quick measurements of relative humidity and temperature in cavities Using permanently programmed sorption isotherms, weight or mass percentages can be determined for various building and insulation materials as well as for hard and soft wood. The measuring device has a thin, flexible sensor tube (gooseneck) and is therefore particularly suitable for moisture analyses, e.g. damage assessment or building drying. Testing the readiness for laying floor and wall coverings is also one of the possible areas of application.   Features and Benefits • Handy pocket-sized moisture meter for lightning-fast individual or series measurements • Simultaneous display of up to three measured values ​​via the 3-line LCD display, resolution: 0.1 % or 0.1° C • Automatic calculation of dew point temperature, wood moisture equilibrium (UGL) *, absolute humidity in g/m³, enthalpy in kJ/K, wet bulb temperature in °C and water activity (aw) • Sorption isotherms for hard and soft wood as well as for 10 different types of building materials • Min, max and hold function for the measured values • Storage of the last 5 measured values • Automatic device shutdown     Further versions The Hydromette Compact RH-T Flex is also available with a longer gooseneck (350mm instead of 250mm). The manufacturer Gann is one of the leading producers of high-quality moisture measuring devices from Germany. Gann measuring devices are considered standard among working instruments among professionals in building drying and water damage drying. They are also recognized by damage experts in insurance companies.    Technical data   Gann Article No.: 31013142 Measuring range: Humidity: 0 – 100 % RH ± 1.8 % RH (10 – 90 % RH) Air temperature: -20 to +70 °C ± 0.5 °C (-10 to +70 °C) sensor tube: 350 x Ø 6.5 mm (gooseneck) Advertisement: device/ambient temperature Automatic saving: last 5 measurements Calibration: Automatically Device shutdown: Automatically Power supply: 9-V block battery (included) Dimensions (L x W x H): 175 x 50 x 30 mm Total length with probe approx. 440mm Weight: 180 gr. Special features: No separate electrodes or cables required 9V block battery included Guarantee: 2 years

Read more less