dryer

From the "Top Ten" list of the most economical room air dryers: The Dryfix "Swiss" is an excellent dryer for single-family homes with drying rooms of up to 15m² and approx. 40m clotheslines. It is economical and quieter than room air dryers with comparable drying performance. The elegant, relatively slim metal housing fits perfectly into the room. To install, the support rail is fixed to the wall with two screws, and the dryer can then simply be hung on it. Rubber buffers prevent the (very slight) vibration from being transferred to the wall. The condensate is led via a hose either directly into a drain or into a bucket underneath the device. The air intake is on the side (right), and the coarse dust filter can be easily pulled out to the front for cleaning.  Drying programs: The controls are located on the side of the housing. A toggle switch is used to select whether you want the "laundry drying" or "room monitoring" mode. The desired residual moisture can be easily regulated using a rotary switch. Drying clothes: The drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. Room monitoring: General room monitoring is used to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the value set on the dial; the ideal value for this mode is around 55-60%. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on.   You can only get Dryfix Swiss from us! It is manufactured exclusively for our company in a specialized factory in Switzerland. ambient temperature Technically, the "Swiss" dryers can be used down to 5°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C. mounting on the wall  As with all tumble dryers, installation is extremely simple: a mounting rail is anchored into the wall with 2 screws, and the device can then be hung up. All necessary installation material such as screws/anchors and 1m of hose is included in the scope of delivery. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the sink using the hose if possible. If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range to which the dryer can be mounted.   If you wish, we can professionally install the dryer at your home. Price on request. Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved.   Technical data drying room: up to 15m² Drying performance: 1.73 Kg/h Consumption per kg of laundry: 0.307 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: 530W sound pressure level (our measurement): 1.0 m distance 60 dB(A) 2.5 m distance 57 dB(A) Dehumidification performance: 26 liters/day (30°C / 80% RH) air circulation volume: 600m³/h condensate tank: No integrated tank With hose connection the water directly into the drain or into a bucket. Compressor: rotary compressor Coolant: R410A Dimensions (H/W/D): 55 x 57 x 26 cm (depth: from wall to front) Weight: 35 kg Operating setting: hygrostat wheel Ambient temperature: 5°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years Special features: Made in Switzerland

Read more less

The Bora 208 from Roth-Kippe is an affordable, well-designed dryer for families with children and for households that don't want to tumble dry all their laundry. It dries about 2-3 washing machine loads per day and is available as the "Bora208" (without switchable heating) or the "Bora208H" (with switchable heating). The version with heating can be used to heat the room to 18°C ​​in cooler environments at the touch of a button. In rooms that are 18°C ​​or more all year round, the version with heating is therefore of no advantage. service The Bora has a clear, digital control panel, which can be set in different languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on. Specially for the Bora: By pressing the program button several times, the start time can be delayed by half an hour. This means that you can hang up the laundry during the day, for example, but postpone the drying time until the electricity tariff is low. Switchable heating: For a small additional charge, the device is also available as the "Bora 208 H". The switchable 1000W heater speeds up laundry drying in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on.  Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5m long, which can be 2m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70m from the top edge of the device. Selectable fan speeds: The Boras have one fan speed, i.e. on or off. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or above.  Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland. This allows the dryer to be started with a time delay if desired, so that the low-power tariff can be consistently exploited. Both when drying laundry and when generally stabilizing excessive basement humidity. Daily blocking times or an automatic, time-limited room drying program - for example limited to the night hours - can also be programmed (each limited to a maximum of 99 days). The device counts the operating hours and reminds you after 300 hours with a light that the filter should be cleaned. By pressing the reset button for 5 seconds, the counter is reset and starts again. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: - the plug-in device - Support rail with screws/dowels - hose connection coupling - 2m condensate hose - Operating instructions A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the "Dryfix-Mobil" chassis with integrated bucket or the matching chassis from Roth-Kippe.  Technical data  drying room: up to 15 m² Drying performance: 1.49 Kg/h Consumption per kg of laundry: 0.31 kWh Energy efficiency: A1 Tension: 230V / 50Hz Examples of dehumidification performance and consumption: Consumption max. 515W, with heating switched on: +1000W = total 1515W (only 208H) at 20°C / 80% RH 22.9 L/24h (power consumption: 450 W) at 26°C / 80% RH 27.5 L/24h (power consumption: 495 W) Sound pressure level: 1 m distance 70 dB(A) 2.5 m distance 67 dB(A) (our measurement) air circulation volume: 770 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407C Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 40 kg Operating setting: Digital Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:   Training video on changing the humidity level:   Training video on changing the display language:   Training video for setting the time:

Read more less

The Bora 208 from Roth-Kippe is a cheap, well-designed dryer for families with children and for households that don't want to tumble dry all their laundry. It dries about 2-3 washing machine loads per day and is available as the "Bora208" (without switchable heating) or the "Bora208H" (with switchable heating). The version with heating can be used to heat the room to 18°C ​​in cooler environments at the touch of a button. In rooms that are 18°C ​​or more all year round, the version with heating is therefore of no advantage. service The Bora has a clear, digital control panel that can be set to different languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on. Specially for the Bora: By pressing the program button several times, the start time can be delayed by half an hour. This means that you can hang up the laundry during the day, for example, but postpone the drying time until the electricity tariff is low. Switchable heating: For a small additional charge, the device is also available as the "Bora 208 H". The switchable 1000W heater speeds up laundry drying in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on.  Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5m long, which can be 2m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70m from the top edge of the device. Selectable fan speeds: The Boras have one fan speed, i.e. on or off. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or above.  Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland. This allows the dryer to be started with a time delay if desired, so that the low-power tariff can be consistently exploited. Both when drying laundry and when generally stabilizing excessive basement humidity. Daily blocking times or an automatic, time-limited room drying program - for example limited to the night hours - can also be programmed (each limited to a maximum of 99 days). The device counts the operating hours and reminds you after 300 hours with a light that the filter should be cleaned. By pressing the reset button for 5 seconds, the counter is reset and starts again. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: - the plug-in device - Support rail with screws/dowels - hose connection coupling - 2m condensate hose - Operating instructions A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the "Dryfix-Mobil" chassis with integrated bucket or the matching chassis from Roth-Kippe.  Technical data  drying room: up to 15 m² Drying performance: 1.49 Kg/h Consumption per kg of laundry: 0.31 kWh Energy efficiency: A1 Tension: 230V / 50Hz Examples of dehumidification performance and consumption: Consumption max. 515W, with heating switched on: +1000W = total 1515W (only 208H) at 20°C / 80% RH 22.9 L/24h (power consumption: 450 W) at 26°C / 80% RH 27.5 L/24h (power consumption: 495 W) Sound pressure level: 1 m distance 70 dB(A) 2.5 m distance 67 dB(A) (our measurement) air circulation volume: 770 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407C Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 40 kg Operating setting: Digital Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:   Training video on changing the humidity level:   Training video on changing the display language:   Training video for setting the time:

Read more less

The new WT230D is a successful development of its predecessor, the WT230U. It is a little more powerful in terms of dehumidification performance and, with significantly lower consumption, is at the forefront in terms of efficiency. An ideal device for single-family homes in combination with a tumble dryer. service The device is very easy to operate using the easy-to-understand digital controls on the front. The display provides the current information about the room status and the selected program. The display languages ​​available are German, French, Italian and English. Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. With the help of three pre-programmed drying levels, you can choose between partially dry, iron-dry or cupboard dry. All pre-programmed moisture values ​​can be changed at any time according to your own wishes. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on. In both programs, both the current humidity and the target humidity are visible on the display. Blower and fan speeds: The blower is an electronically operated, economical radial fan. The dry air jet goes slightly downwards from the outlet, which means that the air is blown into the lower part of the laundry, where the laundry is normally the wettest. This falling wind tunnel is also very practical if you set up a clothes rack in front of the device. Selectable fan settings: The WT tumble dryers are the only devices of this type where the fan setting can be regulated. Even the weaker setting has a very respectable air flow, but significantly reduces the operating noise. If the laundry hanger is fully loaded, the strong fan setting is recommended in order to force the dry air through the laundry as forcefully as possible. This produces faster and more even drying results. On the strong setting, the dry air jet can also reach items of laundry that are far away, up to around 7m away. Adjustable air slats: Flexible slats are attached to the air outlet, which can be adjusted laterally and in height so that the air can be adjusted more precisely to the length/width of the clothesline. Direct hose connection: The water extracted from the laundry runs into a hose which, on the WT devices, is attached slightly below the back wall, rather than on the underside of the device as is usual. This is an advantage over other models if the gradient to the drain is not very great or if the device is to be hung a little lower. There is no pump integrated into the device, so the hose must have a constant gradient to the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. We have suitable inlet pipes and buckets in our range if required. Air filter: The moist room air is sucked in at the top of the front. A magnetically attached filter with a frame cleans the air of coarse dust and fluff so that the inside of the device remains clean. The filter consists of a very fine, close-meshed nylon net. This has a high cleaning power, is easy to clean and, if treated correctly, usually lasts for the entire life of the dryer. Memory function: The settings are saved in the room monitoring program. If the power is interrupted, the dryer will resume operation with the same settings. It is therefore also suitable for operation with a timer, for example if you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted. Room temperature: Technically, Aerial's WT dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe: The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing institute for tumble dryers, "Swiss Testing". Service-friendly device construction: The entire cover can be removed from the device in just a few easy steps. This makes handling easier when cleaning or servicing is required, as the device does not have to be removed from the wall.  mounting on the wall As with all tumble dryers, installation is extremely simple: a mounting rail is anchored into the wall with 2 screws, and the device can then be hung up. All necessary installation material such as screws/anchors and 2m of hose is included in the scope of delivery. Both the support rail and the two buffers in the lower area of ​​the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the sink using the hose if possible (hose is included in the scope of delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range to which the dryer can be mounted. If you wish, we can professionally install the dryer at your home. Price on request. Important: • Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate tradesman, if one does not already exist. • If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved.  Technical data drying room: up to 18 m² Drying performance: 1.63 Kg/h Consumption per kg of laundry: 0.27 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 660W or 420W (at 20°C/60% RH) Sound pressure level: 2.5 m distance 59 dB(A) 2.5 m distance 67 dB(A) fan speed 2 (our measurement) Examples of dehumidification performance and consumption: at 30°C / 80% RH = 35.5 liters / 24h (power consumption: 569 W) at 27°C / 60% RH = 21.1 liters / 24h (power consumption: 487 W) at 20°C / 60% RH = 14.6 liters / 24h (power consumption: 420 W) at 10°C / 70% RH = 6.1 liters / 24h (power consumption: 368 W) air circulation volume: 750 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 40 kg Operating setting: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

The new Secotec 1400 tumble dryer from Lübra impresses with its slim design, economical operation and solid workmanship made in Switzerland. Built similarly to the cheaper Dryfix Swiss, the Secotec1400 has a more powerful blower, which is particularly advantageous for even drying of long lines of linen over 4m long. The drying capacity is 1.70 kg per hour, which corresponds to around 3-4 washing machine loads per day in slightly temperate rooms. The Secotec 1400 is therefore ideal when used in single-family homes or in apartment buildings as a supplement to a tumble dryer. The moist room air is sucked in from the right side, and the dry air is blown into the room from the front in the upper part of the housing. The Secotec1400 is ideal for drying laundry if the upper edge is not mounted higher than 1.70m and can blow lengthways through the linen. The housing is made of high-quality, powder-coated metal (white RAL 9003). A dust filter is inserted on the right side, which cleans the air drawn in from dirt. This filter consists of a plastic frame and a high-density nylon net. It can be easily removed from the front for cleaning. The water drainage channel for the condensate is located directly behind the filter, which can therefore be accessed for cleaning without tools. Easy operation with the Lübra control • Function switch: here you can choose whether the device should only dry the laundry and then switch off automatically, or whether it should keep the room at a constant target humidity. In this mode, the dryer always runs when the room humidity is higher than the set desired humidity, otherwise the dehumidification and fan pause. • Hygrostat wheel: Rotary switch with which the desired target humidity can be easily regulated. • Start button: If you do not want to change any of the settings, you can start (or stop) the operation by simply pressing the start button. This is an easy-to-understand solution, particularly in drying rooms for several parties. A plexiglass cover is also available on request, which prevents access to the function wheel and hygrostat so that the settings cannot be changed. ambient temperature Technically, Secotec tumble dryers can be used down to 5°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C.  mounting on the wall As with all tumble dryers, installation is extremely simple: a mounting rail is anchored into the wall using 2 screws, and the device can then be hung up. All necessary mounting material such as screws/anchors and 1m of hose is included in the delivery. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (suitable hose: 16mm inner diameter). If you want to use a bucket, please ensure that it has enough capacity (min. 8 liters) to avoid overflowing while drying laundry.   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved.   Technical data   drying room: up to 18m2 Drying performance: 1.7 kg/h Consumption per kg of laundry: 0.27 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: 460W sound pressure level (our measurement): 1.0 m distance 66 dB(A) 2.5 m distance 63 dB(A) Dehumidification performance: 35 liters/day (30°C / 80% RH) air circulation volume: 850m³/h condensate tank: No integrated tank With hose connection the water directly into the drain or into a bucket. Compressor: rotary compressor Coolant: R410C Dimensions (H/W/D): 550 x 570 x 260 mm (depth: from wall to front) Weight: 35 kg Operating setting: hygrostat wheel Ambient temperature: 5°C ~ 30°C Swiss plug: Yes, connection cable 3m hose connection: Yes Guarantee: 3 years

Read more less

An ideal dryer for households that don't want to tumble dry all their laundry. It dries about 2-3 loads of laundry per day. The model offered here does not have a switchable heater.   The 408 is the successor to the "Bora 208". It is visually very similar and identical to its predecessor in terms of compact dimensions. However, it has been technically updated: the new, more environmentally friendly refrigerant "R32" brings improved efficiency. The ventilation can now be regulated in 3 stages, which significantly reduces the operating noise on the lower ventilation levels. It also has a user-friendly touchscreen operation and the option of a WLAN connection.     service The Bora has a clear, digital touchscreen control panel, which can be set to various languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on.  Specially for the Bora: The start time can be moved to a later time if, for example, you only want to dry clothes during the off-peak period. It is also possible to set blocking times during which the device never runs. It is also possible for the dryer to automatically switch to room monitoring mode once the laundry has finished drying. Switchable heating ("H" models): For a small additional charge, the device is also available as the "Bora 408 H". The switchable 1000 W heater speeds up the drying of laundry in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on. The version with heater is therefore only an advantage in rooms that fall below 18°C ​​in the cold season.   Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5 m long, which can be 2 m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70 m from the top edge of the device. Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly ECO = Consumption and drying speed are in the average range of the specified performance data Fast = High air flow for fast, efficient drying. The operating noise is clearly noticeable. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. The new model also improves the hold and opening of the door with magnets.   Wi-Fi: The WiFi connection allows you to display the BORA status via a browser on your smartphone, tablet or PC. The WiFi connection also gives you access to software updates. Of course, you can also operate the device as usual directly without WiFi. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or top.   Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland.   Funny gadget: if you don't want to get used to the new control panel, you can switch to the old design at the touch of a button. The control panel on the display then looks practically identical to the buttons on the previous model. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: • the plug-in device • Support rail with screws/dowels • Hose connection coupling • 2 m condensate hose • Operating instructions   A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the appropriate chassis from Roth-Kippe.  Technical data  drying room: up to 15 - 18 m² Drying performance: 1.45 - 1.89 kg/h depending on fan speed Consumption per kg of laundry: 0.25 - 0.31 kWh depending on fan level Energy efficiency: A Tension: 230V / 50Hz Power consumption: during normal operation in "ECO" mode 0.41 kW with heating switched on ("H" models): 1.41 kW Sound pressure level: Fan level 1: 45 dB(A) Fan level 3: 66 dB(A) (Manufacturer's information at 3 m distance) air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R32 (GWP 675) Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 38 kg Operating setting: touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:    

Read more less

An ideal dryer for families with children. It dries about 3-4 loads of laundry per day. The model offered here does not have a switchable heater.   The 410 is the successor to the "Bora 210". It is visually very similar and identical to its predecessor in terms of compact dimensions. However, it has been technically updated: the new, more environmentally friendly refrigerant "R32" brings improved efficiency. The ventilation can now be regulated in 3 stages, which significantly reduces the operating noise on the lower ventilation levels. It also has a user-friendly touchscreen operation and the option of a WLAN connection.     service The Bora has a clear, digital touchscreen control panel, which can be set to various languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on.  Specially for the Bora: The start time can be moved to a later time if, for example, you only want to dry clothes during the off-peak period. It is also possible to set blocking times during which the device never runs. It is also possible for the dryer to automatically switch to room monitoring mode once the laundry has finished drying. Switchable heating ("H" models): For a small additional charge, the device is also available as the "Bora 410 H". The switchable 1000 W heater speeds up laundry drying in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on. The version with heater is therefore only an advantage in rooms that fall below 18°C ​​in the cold season.   Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5 m long, which can be 2 m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70 m from the top edge of the device. Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly ECO = Consumption and drying speed are in the average range of the specified performance data Fast = High air flow for fast, efficient drying. The operating noise is clearly noticeable. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. The new model also improves the hold and opening of the door with magnets.   Wi-Fi: The WiFi connection allows you to display the BORA status via a browser on your smartphone, tablet or PC. The WiFi connection also gives you access to software updates. Of course, you can also operate the device as usual directly without WiFi. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or top.   Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland.   Funny gadget: if you don't want to get used to the new control panel, you can switch to the old design at the touch of a button. The control panel on the display then looks practically identical to the buttons on the previous model. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: • the plug-in device • Support rail with screws/dowels • Hose connection coupling • 2 m condensate hose • Operating instructions   A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the appropriate chassis from Roth-Kippe.  Technical data  drying room: up to 25 m² Drying performance: 1.75 - 2.50 kg/h depending on fan speed Consumption per kg of laundry: 0.22 - 0.28 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: during normal operation in "ECO" mode 0.43 kW with heating switched on ("H" models): 1.43 kW Sound pressure level: Fan level 1: 46 dB(A) Fan level 3: 67 dB(A) (Manufacturer's information at 3 m distance) air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R32 (GWP 675) Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 40 kg Operating setting: touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:    

Read more less

An ideal dryer for households that don't want to tumble dry all their laundry. It dries about 2-3 washing machine loads per day. The model offered here has a switchable heater.   The 408H is the successor to the "Bora 208H". It is visually very similar and identical to its predecessor in terms of compact dimensions. However, it has been technically updated: the new, more environmentally friendly refrigerant "R32" brings improved efficiency. The ventilation can now be regulated in 3 stages, which significantly reduces the operating noise on the lower ventilation levels. It also has a user-friendly touchscreen operation and the option of a WLAN connection.     service The Bora has a clear, digital touchscreen control panel, which can be set to various languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on.  Specially for the Bora: The start time can be moved to a later time if, for example, you only want to dry clothes during the off-peak period. It is also possible to set blocking times during which the device never runs. It is also possible for the dryer to automatically switch to room monitoring mode once the laundry has finished drying. Switchable heating ("H" models): The switchable 1000 W heater speeds up laundry drying in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on. The version with heater is therefore only advantageous in rooms that fall below 18°C ​​in the cold season.  Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5 m long, which can be 2 m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70 m from the top edge of the device. Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly ECO = Consumption and drying speed are in the average range of the specified performance data Fast = High air flow for fast, efficient drying. The operating noise is clearly noticeable. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. The new model also improves the hold and opening of the door with magnets.   Wi-Fi: The WiFi connection allows you to display the BORA status via a browser on your smartphone, tablet or PC. The WiFi connection also gives you access to software updates. Of course, you can also operate the device as usual directly without WiFi. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or top.   Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland.   Funny gadget: if you don't want to get used to the new control panel, you can switch to the old design at the touch of a button. The control panel on the display then looks practically identical to the buttons on the previous model. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: • the plug-in device • Support rail with screws/dowels • Hose connection coupling • 2 m condensate hose • Operating instructions   A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the appropriate chassis from Roth-Kippe.  Technical data  drying room: up to 15 - 18 m² Drying performance: 1.45 - 1.89 kg/h depending on fan speed Consumption per kg of laundry: 0.25 - 0.31 kWh depending on fan level Energy efficiency: A Tension: 230V / 50Hz Power consumption: during normal operation in "ECO" mode 0.41 kW with heating switched on ("H" models): 1.41 kW Sound pressure level: Fan level 1: 45 dB(A) Fan level 3: 66 dB(A) (Manufacturer's information at 3 m distance) air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R32 (GWP 675) Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 38 kg Operating setting: touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:    

Read more less

The dryer is suitable for single-family homes and drying rooms with small to medium drying requirements. It has various functions, which combine the previous separation into AH (endless operation) and E (end-off) models in one device: drying programs drying clothes It is operated at the touch of a button. You can choose between light, medium or high drying levels. The tumble dryer works fully automatically and, similar to the previous models, with what is known as an end-off control, which means that it dehumidifies until the laundry is dry and then switches off automatically. If you want to use the device again, you have to restart it manually. basement dehumidification The dryer is also equipped with a button for keeping the room dry. The device runs whenever the humidity is too high and there is a risk of mold/odors forming in the basement. If the humidity is right, the device stops.   timer function It is also possible to operate the device manually for 30, 60 or 90 minutes. After the time has elapsed, the device switches off and manual operation is automatically switched off.     execution Compact device with powerful ventilation. Slats for air outlet, which can be adjusted horizontally if required. The clearly laid out control panel is limited to 4 buttons on the front. The support rail and the two spacer buffers in the lower part of the device are insulated with rubber to reduce the transmission of sound to the wall. The mouse-gray color of the housing is individually pleasing. Heating option : This model is also available with a 1350W heater for an additional charge. This switches on automatically at 14°C (or colder) and heats until the room temperature reaches 16°C. This heater is therefore only useful in very cold drying rooms. If the room is 16°C or warmer all year round, the version with heater offers no advantage. Technically, the Seccomat tumble dryers can be used down to 10°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.   scope of delivery The delivery includes the device with support rail, all necessary mounting material and a drain set. The drain set consists of a water tank, drain hose and suitable hose connection couplings.   assembly If you wish, we can professionally install the dryer at your home for CHF 210.-. Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If wall mounting is not possible, we recommend the appropriate Secomat chassis.    Technical data  Krüger article: 386.01 drying room: up to 15 m² Drying performance: 1.36 Kg/h Consumption per kg of laundry: 0.27 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 345W or 325W (at 20°C/60% RH) Version with heating "75H": Heating switched on = +1350W Sound pressure level: 64 dB(A) (manufacturer's specification with 7.5kg of laundry in the room) Example of dehumidification performance and consumption: at 20°C / 60% RH = 9.0 liters / 24h (power consumption: 325 W) air circulation volume: 930 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R134a / 550g Dimensions (H/W/D): 620 x 545 x 330 mm Weight: 39 kg Operating setting: program keys Ambient temperature: 10°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

An ideal dryer for families with children. It dries about 3-4 loads of laundry per day. The model offered here has a switchable heater.   The 410H is the successor to the "Bora 210H". It is visually very similar and identical to its predecessor in terms of compact dimensions. However, it has been technically updated: the new, more environmentally friendly refrigerant "R32" brings improved efficiency. The ventilation can now be regulated in 3 stages, which significantly reduces the operating noise on the lower ventilation levels. It also has a user-friendly touchscreen operation and the option of a WLAN connection.     service The Bora has a clear, digital touchscreen control panel, which can be set to various languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on.  Specially for the Bora: The start time can be moved to a later time if, for example, you only want to dry clothes during the off-peak period. It is also possible to set blocking times during which the device never runs. It is also possible for the dryer to automatically switch to room monitoring mode once the laundry has finished drying. Switchable heating ("H" models): The switchable 1000 W heater speeds up laundry drying in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on. The version with heater is therefore only advantageous in rooms that fall below 18°C ​​in the cold season.  Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5 m long, which can be 2 m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70 m from the top edge of the device. Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly ECO = Consumption and drying speed are in the average range of the specified performance data Fast = High air flow for fast, efficient drying. The operating noise is clearly noticeable. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. The new model also improves the hold and opening of the door with magnets.   Wi-Fi: The WiFi connection allows you to display the BORA status via a browser on your smartphone, tablet or PC. The WiFi connection also gives you access to software updates. Of course, you can also operate the device as usual directly without WiFi. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or top.   Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland.   Funny gadget: if you don't want to get used to the new control panel, you can switch to the old design at the touch of a button. The control panel on the display then looks practically identical to the buttons on the previous model. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: • the plug-in device • Support rail with screws/dowels • Hose connection coupling • 2 m condensate hose • Operating instructions   A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the appropriate chassis from Roth-Kippe.  Technical data  drying room: up to 25 m² Drying performance: 1.75 - 2.50 kg/h depending on fan speed Consumption per kg of laundry: 0.22 - 0.28 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: during normal operation in "ECO" mode 0.43 kW with heating switched on ("H" models): 1.43 kW Sound pressure level: Fan level 1: 46 dB(A) Fan level 3: 67 dB(A) (Manufacturer's information at 3 m distance) air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R32 (GWP 675) Dimensions (H/W/D): 70.5 x 45 x 33.5 cm Weight: 40 kg Operating setting: touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:    

Read more less

If you like your laundry to dry more quickly, the WT 240D is a good, powerful machine. The WT240 is the most economical of the new WT series from Aerial. A reliable helper in busy laundry rooms. service The device is very easy to operate using the easy-to-understand digital controls on the front. The display provides the current information about the room status and the selected program. The display languages ​​available are German, French, Italian and English. Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. With the help of three pre-programmed drying levels, you can choose between partially dry, iron-dry or cupboard dry. All pre-programmed moisture values ​​can be changed at any time according to your own wishes. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on. In both programs, both the current humidity and the target humidity are visible on the display. Blower and fan speeds: The blower is an electronically operated, economical radial fan. The dry air jet goes slightly downwards from the outlet, which means that the air is blown into the lower part of the laundry, where the laundry is normally the wettest. This falling wind tunnel is also very practical if you set up a clothes rack in front of the device. Selectable fan settings: The WT tumble dryers are the only devices of this type where the fan setting can be regulated. Even the weaker setting has a very respectable air flow, but significantly reduces the operating noise. If the laundry hanger is fully loaded, the strong fan setting is recommended in order to force the dry air through the laundry as forcefully as possible. This produces faster and more even drying results. On the strong setting, the dry air jet can also reach items of laundry that are far away, up to around 8m away. Adjustable air slats: Flexible slats are attached to the air outlet, which can be adjusted laterally and in height so that the air can be adjusted more precisely to the length/width of the clothesline. Direct hose connection: The water extracted from the laundry runs into a hose which, on the WT devices, is attached slightly below the back wall, rather than on the underside of the device as is usual. This is an advantage over other models if the gradient to the drain is not very great or if the device is to be hung a little lower. There is no pump integrated into the device, so the hose must have a constant gradient to the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. We have suitable inlet pipes and buckets in our range if required. Air filter: The moist room air is sucked in at the top of the front. A magnetically attached filter with a frame cleans the air of coarse dust and fluff so that the inside of the device remains clean. The filter consists of a very fine, close-meshed nylon net. This has a high cleaning power, is easy to clean and, if treated correctly, usually lasts for the entire life of the dryer. Memory function: The settings are saved in the room monitoring program. If the power is interrupted, the dryer will resume operation with the same settings. It is therefore also suitable for operation with a timer, for example if you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted. Room temperature: Technically, Aerial's WT dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe: The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing institute for tumble dryers, "Swiss Testing". Service-friendly device construction: The entire cover can be removed from the device in just a few easy steps. This makes handling easier when cleaning or servicing is required, as the device does not have to be removed from the wall.  mounting on the wall As with all tumble dryers, installation is extremely simple: a mounting rail is anchored into the wall with 2 screws, and the device can then be hung up. All necessary installation material such as screws/anchors and 2m of hose is included in the scope of delivery. Both the support rail and the two buffers in the lower area of ​​the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the sink using the hose if possible (hose is included in the scope of delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range to which the dryer can be mounted. If you wish, we can professionally install the dryer at your home. Price on request. Important: • Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate tradesman, if one does not already exist. • If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved.  Technical data drying room: up to 20 m² Drying performance: 1.93 Kg/h Consumption per kg of laundry: 0.26 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 620W or 440W (at 20°C/60% RH) Sound pressure level: 2.5 m distance 62 dB(A) 2.5 m distance 68 dB(A) fan speed 2 (our measurement) Examples of dehumidification performance and consumption: at 30°C / 80% RH = 36.5 L/24h (power consumption: 570 W) at 27°C / 60% rH = 21.6 L/24h (power consumption: 500 W) at 20°C / 60% rH = 16.8 L/24h (power consumption: 440 W) at 10°C / 70% rH = 7.2 L/24h (power consumption 390 W) air circulation volume: 830 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 40 kg Operating setting: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

The dryer is suitable for single-family homes with smaller drying requirements, especially for rooms that can get a little cooler in winter. It has various functions that combine the previous separation into AH (endless operation) and E (end-off) models in one device: drying programs drying clothes It is operated at the touch of a button. You can choose between light, medium or high drying levels. The tumble dryer works fully automatically and, similar to the previous models, with what is known as an end-off control, which means that it dehumidifies until the laundry is dry and then switches off automatically. If you want to use the device again, you have to restart it manually. basement dehumidification The dryer is also equipped with a button for keeping the room dry. The device runs whenever the humidity is too high and there is a risk of mold/odors forming in the basement. If the humidity is right, the device stops. timer function It is also possible to operate the device manually for 30, 60 or 90 minutes. After the time has elapsed, the device switches off and manual operation is automatically switched off.   execution Compact device with powerful ventilation. Slats for air outlet, which can be adjusted horizontally if required. The clearly laid out control panel is limited to 4 buttons on the front. The support rail and the two spacer buffers in the lower part of the device are insulated with rubber to reduce the transmission of sound to the wall. The mouse-gray color of the housing is individually pleasing. Heating : This model is equipped with a 1350W heater. This switches on automatically at 14°C (or colder) and heats until the room temperature is 16°C. This heater is therefore only useful in very cold drying rooms. If the room is 16°C or warmer all year round, the version with heating is of no advantage. In this case, consider the standard version "Secomat75" Technically, the devices can be used down to 10°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C. scope of delivery The delivery includes the device with support rail, all necessary mounting material and a drain set. The drain set consists of a water tank, drain hose and suitable hose connection couplings. assembly If you wish, we can professionally install the dryer at your home for CHF 210.-. Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If wall mounting is not possible, we recommend the appropriate Secomat chassis.  Technical data  Krüger article: 386.04 drying room: up to 15 m² Drying performance: 1.36 Kg/h Consumption per kg of laundry: 0.27 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 370W or 345W (at 20°C/60% RH) Heating switched on = +1350W Sound pressure level: 64 dB(A) (manufacturer's specification with 7.5kg of laundry in the room) Example of dehumidification performance and consumption: at 20°C / 60% RH = 9.0 liters / 24h (power consumption: 345 W) air circulation volume: 930 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R134a / 550g Dimensions (H/W/D): 620 x 545 x 330 mm Weight: 39 kg Operating setting: program keys Ambient temperature: 10°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

The WT 250D is not only suitable for intensive drying tasks in single-family homes, but also meets the performance expectations in drying rooms that are shared by several parties. With a drying capacity of around 3 kg of laundry per hour, this model dries what a washing machine can wash in around 2.5 hours. service The device is very easy to operate using the easy-to-understand digital controls on the front. The display provides the current information about the room status and the selected program. The display languages ​​available are German, French, Italian and English. Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. With the help of three pre-programmed drying levels, you can choose between partially dry, iron-dry or cupboard dry. All pre-programmed moisture values ​​can be changed at any time according to your own wishes. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on. In both programs, both the current humidity and the target humidity are visible on the display. Blower and fan speeds: The blower is an electronically operated, economical radial fan. The dry air jet goes slightly downwards from the outlet, which means that the air is blown into the lower part of the laundry, where the laundry is normally the wettest. This falling wind tunnel is also very practical if you set up a clothes rack in front of the device. Selectable fan settings: The WT tumble dryers are the only devices of this type where the fan setting can be regulated. Even the weaker setting has a very respectable air flow, but significantly reduces the operating noise. If the laundry hanger is fully loaded, the strong fan setting is recommended in order to force the dry air through the laundry as forcefully as possible. This produces faster and more even drying results. On the strong setting, the dry air jet can also reach items of laundry that are far away, up to around 9m away. Adjustable air slats: Flexible slats are attached to the air outlet, which can be adjusted laterally and in height so that the air can be adjusted more precisely to the length/width of the clothesline. Direct hose connection: The water extracted from the laundry runs into a hose which, on the WT devices, is attached slightly below the back wall, rather than on the underside of the device as is usual. This is an advantage over other models if the gradient to the drain is not very great or if the device is to be hung a little lower. There is no pump integrated into the device, so the hose must have a constant gradient to the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. We have suitable inlet pipes and buckets in our range if required. Air filter: The moist room air is sucked in at the top of the front. A magnetically attached filter with a frame cleans the air of coarse dust and fluff so that the inside of the device remains clean. The filter consists of a very fine, close-meshed nylon net. This has a high cleaning power, is easy to clean and, if treated correctly, usually lasts for the entire life of the dryer. Memory function: The settings are saved in the room monitoring program. If the power is interrupted, the dryer will resume operation with the same settings. It is therefore also suitable for operation with a timer, for example if you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted. Room temperature: Technically, Aerial's WT dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe: The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing institute for tumble dryers, "Swiss Testing". Service-friendly device construction: The entire cover can be removed from the device in just a few easy steps. This makes handling easier when cleaning or servicing is required, as the device does not have to be removed from the wall.  mounting on the wall As with all tumble dryers, installation is extremely simple: a mounting rail is anchored into the wall with 2 screws, and the device can then be hung up. All necessary installation material such as screws/anchors and 2m of hose is included in the scope of delivery. Both the support rail and the two buffers in the lower area of ​​the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the sink using the hose if possible (hose is included in the scope of delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range to which the dryer can be mounted. If you wish, we can professionally install the dryer at your home. Price on request. Important: • Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate tradesman, if one does not already exist. • If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved.  Technical data drying room: up to 35 m² Drying performance: 2.95 Kg/h Consumption per kg of laundry: 0.27 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 950W or 677W (at 20°C/60% RH) Sound pressure level: 2.5 m distance 61 dB(A) 2.5 m distance 68 dB(A) fan speed 2 (our measurement) Examples of dehumidification performance and consumption: at 30°C / 80% rH = 57.1 Ll/24h (power consumption: 570 W) at 27°C / 60% RH = 24.1 L/24h (power consumption: 500 W) at 20°C / 60% rH = 23.0 L/24h (power consumption: 440 W) at 10°C / 70% RH = 13.4 L/24h (power consumption: 390 W) air circulation volume: 950 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 42 kg Operating setting: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

This powerful device is suitable for single-family homes with large amounts of laundry as well as for multi-family drying rooms. It has various functions, which combine the previous separation into AH (endless operation) and E (end-off) models in one device: drying programs drying clothes It is operated at the touch of a button. You can choose between light, medium or high drying levels. The tumble dryer works fully automatically and, similar to the previous models, with what is known as an end-off control, which means that it dehumidifies until the laundry is dry and then switches off automatically. If you want to use the device again, you have to restart it manually. basement dehumidification The dryer is also equipped with a button for keeping the room dry. The device runs whenever the humidity is too high and there is a risk of mold/odors forming in the basement. If the humidity is right, the device stops. timer function It is also possible to operate the device manually for 30, 60 or 90 minutes. After the time has elapsed, the device switches off and manual operation is automatically switched off. execution Compact device with powerful ventilation. Slats for air outlet, which can be adjusted horizontally if required. The clearly laid out control panel is limited to 4 buttons on the front. The support rail and the two spacer buffers in the lower part of the device are insulated with rubber to reduce the transmission of sound to the wall. The mouse-gray color of the housing is individually pleasing. Heating option : This model is also available with a 1350W heater for an additional charge. This switches on automatically at 14°C (or colder) and heats until the room temperature reaches 16°C. This heater is therefore only useful in very cold drying rooms. If the room is 16°C or warmer all year round, the version with heater offers no advantage. Technically, the Secomat tumble dryers can be used down to 10°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C. scope of delivery The delivery includes the device with support rail, all necessary mounting material and a drain set. The drain set consists of a water tank, drain hose and suitable hose connection couplings. assembly If you wish, we can professionally install the dryer at your home for CHF 210.-. Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If wall mounting is not possible, we recommend the appropriate Secomat chassis.  Technical data  Krüger article: 387.01 drying room: up to 25 m² Drying performance: 2.98 Kg/h Consumption per kg of laundry: 0.30 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 989W or 950W (at 20°C/60% RH) Version with heating: Heating switched on = +1350W Sound pressure level: 71 dB(A) (manufacturer's specification for 10kg of laundry in the room) Examples of dehumidification performance and consumption: at 20°C / 60% RH = 28.0 liters / 24h (power consumption: 950 W) air circulation volume: 1200 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407c / 550g Dimensions (H/W/D): 690 x 655 x 395 mm Weight: 47 kg Operating setting: program keys Ambient temperature: 10°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

The new "Secomat2" from Krüger impresses with its very simple operation and well thought-out functionality. The design has been modernized and even won the "Reddot" award. The "Secomat2" is the smallest version, but it dries much more powerfully than its predecessor, the "Secomat75". It achieves a drying performance of around 2 washing machine loads per day. Available in anthracite, and also in azure blue.   service   The basic idea of ​​the new generation is that the dryer only needs to be switched on once. The highly developed software and various sensors then take over operation fully automatically. The following functions can be selected at the touch of a button: • Dry laundry only: the drying process continues until the laundry is dry. If there is no laundry hanging or if the laundry is dry, the appliance pauses. • Drying laundry and room monitoring: if laundry is hanging, it is dried. When the laundry is dry or if there is no laundry hanging, the Secomat switches to general room monitoring. The humidity in the room is kept just below the limit of 60% RH to prevent odors and mold growth. • Room monitoring only: the device can also be used as a room dehumidifier without drying laundry. The humidity in the room is kept just below the limit of 60% RH to prevent odors and mold formation.     Wi-Fi and app   Anyone who wants to monitor or change the dryer and its operation can do so easily via their mobile phone using the well-developed app. To do this, the device must be within range of a WiFi network in the house.     sensors Like most dehumidifiers on the market, the new Secomats also have humidity sensors. These measure the humidity in the room and provide information on the drying process of the laundry. They also control the ventilation level: while very wet laundry releases sufficient moisture even with a low ventilation level, the ventilation is increased the drier the laundry is. This is to optimally blow the residual moisture out of the laundry and to keep the laundry as smooth as possible in the wind. Another sensor is an optical sensor. This remembers the room when it is empty and can therefore detect when laundry is hanging. If laundry is detected, the device switches to laundry drying mode. It can distinguish whether the items are statically hanging (= laundry) or moving objects such as people or animals. Their movement does not trigger the drying process.     airway and filter   The moist room air is sucked in at the front in the lower area, dried and then blown out into the room at high speed in the upper area. An air filter cleans the sucked-in air of dirt and fine dust. It is washable and has been greatly improved compared to previous generations. It is now housed in a solid folding door and is easy to remove.     water drainage   The extracted water is drained away via a hose connection. The connection is in the base of the device near the wall, so that the water runs practically vertically via a hose into a siphon installed underneath. The water can also be drained away sideways using an angle coupling.     assembly   Wall mounting is relatively quick and easy, with little manual skill required. A support rail is fixed to the wall with three screws, and the dryer can then be hung on this support rail. The support rail of the previous generation is compatible, so no new holes need to be drilled. All necessary mounting material such as rail, screws, dowels and hose coupling is included in the delivery.     Features at a glance • Environmentally friendly, natural refrigerant R1270 • Energy efficient through laundry detection • Intuitive operation • App connectivity • Housing made of powder-coated sheet steel • Adjustable air outlet slats • Practical drain set • Easily removable lint filter • Mounting rail for wall mounting • 3.5 m power cable • Color: blue (RAL 5009)     Technical data  Krüger article: 396.03 drying room: min. 6 m² to max. 12 m² Drying performance: 2.13 Kg/h Consumption per kg of laundry: 0.28 kWh Energy efficiency: A Tension: 230V / 50Hz Power consumption: 618W (at 20°C/60% RH) Sound pressure level: 64 dB(A) (manufacturer's specification with 7.5kg of laundry in the room) Examples of dehumidification performance and consumption: n/a air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R1270 / xxxg (GWP: 2) Dimensions (H/W/D): 630 x 512 x 327 mm Weight: 45 kg Operating setting: program keys Ambient temperature: 10 °C ~ 30 °C (our recommendation) 5 °C ~ 30 °C (manufacturer information) Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

The new "Secomat2" from Krüger impresses with its very simple operation and well thought-out functionality. The design has been modernized and even won the "Reddot" award. The "Secomat2" is the smallest version, but it dries much more powerfully than its predecessor, the "Secomat75". It achieves a drying performance of around 2 washing machine loads per day. Available in anthracite, and also in azure blue.  service   The basic idea of ​​the new generation is that the dryer only needs to be switched on once. The highly developed software and various sensors then take over operation fully automatically. The following functions can be selected at the touch of a button: • Dry laundry only: the drying process continues until the laundry is dry. If there is no laundry hanging or if the laundry is dry, the appliance pauses. • Drying laundry and room monitoring: if laundry is hanging, it is dried. When the laundry is dry or if there is no laundry hanging, the Secomat switches to general room monitoring. The humidity in the room is kept just below the limit of 60% RH to prevent odors and mold growth. • Room monitoring only: the device can also be used as a room dehumidifier without drying laundry. The humidity in the room is kept just below the limit of 60% RH to prevent odors and mold formation.     Wi-Fi and app   Anyone who wants to monitor or change the dryer and its operation can do so easily via their mobile phone using the well-developed app. To do this, the device must be within range of a WiFi network in the house.     sensors Like most dehumidifiers on the market, the new Secomats also have humidity sensors. These measure the humidity in the room and provide information on the drying process of the laundry. They also control the ventilation level: while very wet laundry releases sufficient moisture even with a low ventilation level, the ventilation is increased the drier the laundry is. This is to optimally blow the residual moisture out of the laundry and to keep the laundry as smooth as possible in the wind. Another sensor is an optical sensor. This remembers the room when it is empty and can therefore detect when laundry is hanging. If laundry is detected, the device switches to laundry drying mode. It can distinguish whether the items are statically hanging (= laundry) or moving objects such as people or animals. Their movement does not trigger the drying process.     airway and filter   The moist room air is sucked in at the front in the lower area, dried and then blown out into the room at high speed in the upper area. An air filter cleans the sucked-in air of dirt and fine dust. It is washable and has been greatly improved compared to previous generations. It is now housed in a solid folding door and is easy to remove.     water drainage   The extracted water is drained away via a hose connection. The connection is in the base of the device near the wall, so that the water runs practically vertically via a hose into a siphon installed underneath. The water can also be drained away sideways using an angle coupling.     assembly   Wall mounting is relatively quick and easy, with little manual skill required. A support rail is fixed to the wall with three screws, and the dryer can then be hung on this support rail. The support rail of the previous generation is compatible, so no new holes need to be drilled. All necessary mounting material such as rail, screws, dowels and hose coupling is included in the delivery.     Features at a glance • Environmentally friendly, natural refrigerant R1270 • Energy efficient through laundry detection • Intuitive operation • App connectivity • Housing made of powder-coated sheet steel • Adjustable air outlet slats • Practical drain set • Easily removable lint filter • Mounting rail for wall mounting • 3.5 m power cable • Color: anthracite (RAL 7016)     Technical data  Krüger article: 396.01 drying room: min. 6 m² to max. 12 m² Drying performance: 2.13 Kg/h Consumption per kg of laundry: 0.28 kWh Energy efficiency: A Tension: 230V / 50Hz Power consumption: 618W (at 20°C/60% RH) Sound pressure level: 64 dB(A) (manufacturer's specification with 7.5kg of laundry in the room) Examples of dehumidification performance and consumption: n/a air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R1270 / xxxg (GWP: 2) Dimensions (H/W/D): 630 x 512 x 327 mm Weight: 45 kg Operating setting: program keys Ambient temperature: 10 °C ~ 30 °C (our recommendation) 5 °C ~ 30 °C (manufacturer information) Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

The reliable dryer for apartment buildings with up to 6 units. Depending on the fan setting, it only needs 4 hours for 2 washing machine loads, which means it also meets the requirements of highly frequented drying rooms. The model offered here does not have a switchable heater. With a consumption of 0.18 kWh per kg of laundry, the 415 is the most efficient in the new Bora series.   The 415 is the successor to the "Bora 315". It is visually very similar and identical to its predecessor in terms of compact dimensions. However, it has been technically updated: the new, more environmentally friendly refrigerant "R32" brings improved efficiency. The ventilation can now be regulated in 3 stages, which significantly reduces the operating noise on the lower ventilation levels. It also has a user-friendly touchscreen operation and the option of a WLAN connection.     service The Bora has a clear, digital touchscreen control panel, which can be set to various languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on.  Specially for the Bora: The start time can be moved to a later time if, for example, you only want to dry clothes during the off-peak period. It is also possible to set blocking times during which the device never runs. It is also possible for the dryer to automatically switch to room monitoring mode once the laundry has finished drying. Switchable heating ("H" models): For a small additional charge, the device is also available as the "Bora 415 H". The switchable 1000 W heater speeds up laundry drying in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on. The version with heater is therefore only an advantage in rooms that fall below 18°C ​​in the cold season.   Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5 m long, which can be 2 m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70 m from the top edge of the device. Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly ECO = Consumption and drying speed are in the average range of the specified performance data Fast = High air flow for fast, efficient drying. The operating noise is clearly noticeable. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. The new model also improves the hold and opening of the door with magnets.   Wi-Fi: The WiFi connection allows you to display the BORA status via a browser on your smartphone, tablet or PC. The WiFi connection also gives you access to software updates. Of course, you can also operate the device as usual directly without WiFi. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or top.   Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland.   Funny gadget: if you don't want to get used to the new control panel, you can switch to the old design at the touch of a button. The control panel on the display then looks practically identical to the buttons on the previous model. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: • the plug-in device • Support rail with screws/dowels • Hose connection coupling • 2 m condensate hose • Operating instructions   A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the appropriate chassis from Roth-Kippe.  Technical data  drying room: up to 30 m² Drying performance: 2.74 - 4.06 kg/h depending on fan speed Consumption per kg of laundry: 0.18 - 0.24 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: during normal operation in "ECO" mode 0.69 kW with heating switched on ("H" models): 1.69 kW Sound pressure level: Fan level 1: 53 dB(A) Fan level 3: 68 dB(A) (Manufacturer's information at 3 m distance) air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R32 (GWP 675) Dimensions (H/W/D): 77 x 70 x 38.5 cm Weight: 62 kg Operating setting: touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:    

Read more less

The Lübra SecoTec 1410 tumble dryer - from the top ten list - is a high-quality room air tumble dryer and is suitable for drying rooms shared by 2-4 people. Thanks to the new double radial fan, it distributes the 1350m³/h of dry air with good pressure even in larger rooms and is noticeably quieter than dryers with comparable dehumidification performance. Modern design, including END-OFF mode. High water removal even in the cooler seasons. Execution: - Plug-in dryer, robust sheet steel housing, white powder-coated - Wall mounting rail with anti-noise rubber buffer, required screws/dowels - Hygrostat - reusable filter - Laundry drying program with end-off function (when the laundry is dry, the device switches off completely) and room dehumidification program (the device always works when the room humidity is higher than the set target humidity value). Easy operation with the Lübra control • Function switch: here you can choose whether the device should only dry the laundry and then switch off automatically, or whether it should keep the room at a constant target humidity. In this mode, the dryer always runs when the room humidity is higher than the set desired humidity, otherwise the dehumidification and fan pause. • Hygrostat wheel: Rotary switch with which the desired target humidity can be easily regulated. • Start button: If you do not want to change any of the settings, you can start (or stop) the operation by simply pressing the start button. This is an easy-to-understand solution, particularly in drying rooms for several parties. A plexiglass cover is also available on request, which prevents access to the function wheel and hygrostat so that the settings cannot be changed. ambient temperature Technically, Secotec tumble dryers can be used down to 5°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C.   mounting on the wall As with all tumble dryers, installation is extremely simple: a mounting rail is anchored into the wall using 2 screws, and the device can then be hung up. All necessary mounting material such as screws/anchors and 2m of hose is included in the scope of delivery. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the sink using the hose if possible (1m of hose is included in the scope of delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry.   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. Technical data country of production Switzerland energy efficiency class A1 power consumption 800 watts supply voltage 230 V drying capacity at 15kg 2.52 kg/h consumption 0.32 kWh / kg laundry noise level (our measurement) 63 db(A) at 2.5m distance 66 dB(A) at 1m distance air circulation 1350m³/h Room temperature use from 5 - 30 °C Dimensions (HxWxD) / Weight 740 x 440 x 410 mm Weight 42 kg coolant (CFC-free) R410a guarantee 3 years

Read more less

The reliable dryer for apartment buildings with up to 6 units. Depending on the fan setting, it only needs 4 hours for 2 washing machine loads, meaning it also meets the requirements of highly frequented drying rooms. The model offered here has a switchable heater. With a consumption of 0.18 kWh per kg of laundry, the 415 is the most efficient in the new Bora series.   The 415 H is the successor to the "Bora 315 H". It is visually very similar and identical to its predecessor in terms of compact dimensions. However, it has been technically updated: the new, more environmentally friendly refrigerant "R32" brings improved efficiency. The ventilation can now be regulated in 3 stages, which significantly reduces the operating noise on the lower ventilation levels. It also has a user-friendly touchscreen operation and the option of a WLAN connection.     service The Bora has a clear, digital touchscreen control panel, which can be set to various languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on.  Specially for the Bora: The start time can be moved to a later time if, for example, you only want to dry clothes during the off-peak period. It is also possible to set blocking times during which the device never runs. It is also possible for the dryer to automatically switch to room monitoring mode once the laundry has finished drying. Switchable heating ("H" models): The switchable 1000 W heater speeds up laundry drying in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on. The version with heater is therefore only advantageous in rooms that fall below 18°C ​​in the cold season.  Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5 m long, which can be 2 m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70 m from the top edge of the device. Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly ECO = Consumption and drying speed are in the average range of the specified performance data Fast = High air flow for fast, efficient drying. The operating noise is clearly noticeable. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. The new model also improves the hold and opening of the door with magnets.   Wi-Fi: The WiFi connection allows you to display the BORA status via a browser on your smartphone, tablet or PC. The WiFi connection also gives you access to software updates. Of course, you can also operate the device as usual directly without WiFi. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or top.   Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland.   Funny gadget: if you don't want to get used to the new control panel, you can switch to the old design at the touch of a button. The control panel on the display then looks practically identical to the buttons on the previous model. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: • the plug-in device • Support rail with screws/dowels • Hose connection coupling • 2 m condensate hose • Operating instructions   A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the appropriate chassis from Roth-Kippe.  Technical data  drying room: up to 30 m² Drying performance: 2.74 - 4.06 kg/h depending on fan speed Consumption per kg of laundry: 0.18 - 0.24 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: during normal operation in "ECO" mode 0.69 kW with heating switched on ("H" models): 1.69 kW Sound pressure level: Fan level 1: 53 dB(A) Fan level 3: 68 dB(A) (Manufacturer's information at 3 m distance) air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R32 (GWP 675) Dimensions (H/W/D): 77 x 70 x 38.5 cm Weight: 62 kg Operating setting: touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:    

Read more less

The hardest worker among the new Aerial WT dryers! It is specially built for intensive use and dries laundry quickly and reliably while being easy to operate. With a drying capacity of around 3.6 kg of laundry per hour, this model dries what a washing machine can wash in around 2 hours. service The device is very easy to operate using the easy-to-understand digital controls on the front. The display provides the current information about the room status and the selected program. The display languages ​​available are German, French, Italian and English. Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. With the help of three pre-programmed drying levels, you can choose between partially dry, iron-dry or cupboard dry. All pre-programmed moisture values ​​can be changed at any time according to your own wishes. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on. In both programs, both the current humidity and the target humidity are visible on the display. Blower and fan speeds: The blower is an electronically operated, economical radial fan. The dry air jet goes slightly downwards from the outlet, which means that the air is blown into the lower part of the laundry, where the laundry is normally the wettest. This falling wind tunnel is also very practical if you set up a clothes rack in front of the device. Selectable fan settings: The WT280 has a (powerful) fan setting. This provides fast drying results, even with a lot of laundry and long drying rooms of up to approx. 10m. Adjustable air slats: Flexible slats are attached to the air outlet, which can be adjusted laterally and in height so that the air can be adjusted more precisely to the length/width of the clothesline. Direct hose connection: The water extracted from the laundry runs into a hose which, on the WT devices, is attached slightly below the back wall, rather than on the underside of the device as is usual. This is an advantage over other models if the gradient to the drain is not very great or if the device is to be hung a little lower. There is no pump integrated into the device, so the hose must have a constant gradient to the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. We have suitable inlet pipes and buckets in our range if required. Air filter: The moist room air is sucked in at the top of the front. A magnetically attached filter with a frame cleans the air of coarse dust and fluff so that the inside of the device remains clean. The filter consists of a very fine, close-meshed nylon net. This has a high cleaning power, is easy to clean and, if treated correctly, usually lasts for the entire life of the dryer. Memory function: The settings are saved in the room monitoring program. If the power is interrupted, the dryer will resume operation with the same settings. It is therefore also suitable for operation with a timer, for example if you only want to run the dryer during off-peak hours. If the power is interrupted during the laundry drying program, the device goes into standby and must be restarted. Room temperature: Technically, Aerial's WT dryers can be used down to 8°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C. Made in Europe: The WT dryers are manufactured by the Dantherm Group in Europe. They have received very good ratings from the Swiss testing institute for tumble dryers, "Swiss Testing". Service-friendly device construction: The entire cover can be removed from the device in just a few easy steps. This makes handling easier when cleaning or servicing is required, as the device does not have to be removed from the wall.  mounting on the wall As with all tumble dryers, installation is extremely simple: a mounting rail is anchored into the wall with 2 screws, and the device can then be hung up. All necessary installation material such as screws/anchors and 2m of hose is included in the scope of delivery. Both the support rail and the two buffers in the lower area of ​​the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the sink using the hose if possible (hose is included in the scope of delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range to which the dryer can be mounted. If you wish, we can professionally install the dryer at your home. Price on request. Important: • Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate tradesman, if one does not already exist. • If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved.  Technical data drying room: up to 40 m² Drying performance: 3.68 Kg/h Consumption per kg of laundry: 0.29 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 1350W or 950W (at 20°C/60% RH) Sound pressure level: (our measurement) 2.5 m distance 67 dB(A)  Examples of dehumidification performance and consumption: at 30°C / 80% rH = 79.2 L/24h (power consumption: 1390 W) at 27°C / 60% rF = 46.6 L/24h (power consumption: 1080 W) at 20°C / 60% rH = 32.2 L/24h (power consumption: 990 W) at 10°C / 70% RH = 20.3 L/24h (power consumption: 800 W) air circulation volume: 950 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407C Dimensions (H/W/D): 80.9 x 64.0 x 34.5 cm Weight: 43 kg Operating setting: Digital Ambient temperature: 8°C ~ 32°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

This model is suitable for single-family homes with large amounts of laundry and in drying rooms that can get cooler in winter. It has various functions that combine the previous separation into AH (endless operation) and E (end-off) models in one device: drying programs drying clothes It is operated at the touch of a button. You can choose between light, medium or high drying levels. The tumble dryer works fully automatically and, similar to the previous models, with what is known as an end-off control, which means that it dehumidifies until the laundry is dry and then switches off automatically. If you want to use the device again, you have to restart it manually. basement dehumidification The dryer is also equipped with a button for keeping the room dry. The device runs whenever the humidity is too high and there is a risk of mold/odors forming in the basement. If the humidity is right, the device stops. timer function It is also possible to operate the device manually for 30, 60 or 90 minutes. After the time has elapsed, the device switches off and manual operation is automatically switched off.   execution Compact device with powerful ventilation. Slats for air outlet, which can be adjusted horizontally if required. The clearly laid out control panel is limited to 4 buttons on the front. The support rail and the two spacer buffers in the lower part of the device are insulated with rubber to reduce the transmission of sound to the wall. The mouse-gray color of the housing is individually pleasing. Heating : This model is equipped with a 1350W heater. This switches on automatically at 14°C (or colder) and heats until the room temperature is 16°C. This heater is therefore only useful in very cold drying rooms. If the room is 16°C or warmer all year round, the version with heating is of no advantage. In this case, consider the standard version without heating. Technically, the devices can be used down to 10°C. Please note that the drying time for all room air dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C. scope of delivery The delivery includes the device with support rail, all necessary mounting material and a drain set. The drain set consists of a water tank, drain hose and suitable hose connection couplings. assembly If you wish, we can professionally install the dryer at your home for CHF 210.-. Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If wall mounting is not possible, we recommend the appropriate chassis.    Technical data  Krüger article: 387.04 drying room: up to 25 m² Drying performance: 2.98 Kg/h Consumption per kg of laundry: 0.30 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 989W or 950W (at 20°C/60% RH) Version with heating Secomat 100H: Heating switched on = +1350W Sound pressure level: 71 dB(A) (manufacturer's specification for 10kg of laundry in the room) Example of dehumidification performance and consumption: at 20°C / 60% RH = 28.0 liters / 24h (power consumption: 950 W) air circulation volume: 1200 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407c / 550g Dimensions (H/W/D): 690 x 655 x 395 mm Weight: 47 kg Operating setting: program keys Ambient temperature: 10°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less

The most powerful Bora for intensive use in apartment buildings. Depending on the fan setting, it only needs a little more than 3 hours to dry 2 washing machine loads . The model offered here does not have a switchable heater.   The 420 is the successor to the "Bora 320". It is visually very similar and identical to its predecessor in terms of compact dimensions. However, it has been technically updated: the new, more environmentally friendly refrigerant "R32" brings improved efficiency. The ventilation can now be regulated in 3 stages, which significantly reduces the operating noise on the lower ventilation levels. It also has a user-friendly touchscreen operation and the option of a WLAN connection.     service The Bora has a clear, digital touchscreen control panel, which can be set to various languages ​​(German, French, Italian, English). Drying programs: The laundry drying program can be started at the touch of a button. The dehumidifier runs until the laundry is dry and then switches off automatically. The pre-programmed target moisture level of 40% is suitable in most cases, but can otherwise be increased or reduced to any moisture level according to your own preference. Logically, the device runs until it can assume that the laundry is dry. Then it switches off. After a few minutes, 1-3 checks are carried out again with pure circulating air to check whether the moisture level has increased too much, meaning that the laundry may not be completely dry. If so, the Bora dries again; if not, it goes into standby. This follow-up check can optimize the drying result, particularly in drying rooms with only a small amount of laundry or with items of clothing of different thicknesses. The dryer also has a general room monitoring function to prevent mold and odors in the basement. The device switches on automatically whenever the room humidity rises above the mold and odor limit of 60% RH. This humidity value can also be changed as desired. Unlike the laundry drying programs, the dryer never switches off completely in this mode, but only pauses as long as the humidity is right. If the humidity rises again, the drying mode switches back on.  Specially for the Bora: The start time can be moved to a later time if, for example, you only want to dry clothes during the off-peak period. It is also possible to set blocking times during which the device never runs. It is also possible for the dryer to automatically switch to room monitoring mode once the laundry has finished drying. Switchable heating ("H" models): For a small additional charge, the device is also available as the "Bora 420 H". The switchable 1000 W heater speeds up laundry drying in the cold season because warm air can absorb more moisture than cold air. If the heater is switched on, it heats until a room temperature of 18°C ​​is reached. Above 18°C, the heater is inactive, even if it is switched on. The version with heater is therefore only an advantage in rooms that fall below 18°C ​​in the cold season.   Blower and fan speeds: The blower is a radial blower, which is placed in the upper part of the housing. It spreads air relatively widely, but loses power as it goes deeper (in long drying rooms). The Bora is therefore particularly suitable for short to medium-sized laundry lines up to approx. 5 m long, which can be 2 m wide. The dry air jet should blow through the laundry below the clotheslines so that it can swing in the wind. This means that the moisture is released into the room air more quickly and can be intercepted by the dryer. The optimal installation height for the Bora should therefore be slightly below the lines, usually around 1.70 m from the top edge of the device. Selectable fan speeds: Silent = Gentle / Quiet, consumption and drying time increase slightly ECO = Consumption and drying speed are in the average range of the specified performance data Fast = High air flow for fast, efficient drying. The operating noise is clearly noticeable. Air louvres: The front of the housing is fixed, i.e. the blowing direction or the dispersion cannot be changed. Direct hose connection: The water extracted from the laundry drains through a hose connection on the bottom of the housing. There is no pump integrated into the device, so the hose must have a constant gradient towards the drain. If there is no drain, the water can of course also be easily collected in a bucket placed under the device. If required, we have suitable inlet pipes and buckets for all Bora models in our range. Air filter: The moist room air is sucked in at the bottom of the front. The industrial, long-lasting filter mat is inserted in a fold-out door at the bottom. It cleans the air of coarse dust and fluff so that the inside of the device remains clean. If the filter material ever runs out, you can order suitable replacement filter mats from us at any time. The new model also improves the hold and opening of the door with magnets.   Wi-Fi: The WiFi connection allows you to display the BORA status via a browser on your smartphone, tablet or PC. The WiFi connection also gives you access to software updates. Of course, you can also operate the device as usual directly without WiFi. Compact dimensions: The Bora is comparatively narrow and often fits in places in the drying room where other devices are too wide, for example between downpipes or electrical cables. Since all controls are on the front, the Bora does not need any space on the sides or top.   Swiss control: Its comfort control was designed by Roth-Kippe and is manufactured in Switzerland.   Funny gadget: if you don't want to get used to the new control panel, you can switch to the old design at the touch of a button. The control panel on the display then looks practically identical to the buttons on the previous model. ambient temperature Technically, the "Bora" tumble dryers can be used down to 8°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C.  Scope of delivery and wall mounting  As with all tumble dryers, installation is very simple: A support rail is fixed to the wall with 3 screws, the Bora can then be easily hung on. All necessary mounting material is already included in the delivery: • the plug-in device • Support rail with screws/dowels • Hose connection coupling • 2 m condensate hose • Operating instructions   A suitable inlet pipe with bucket is optionally available if the water cannot be drained directly into a drain. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the drain using the hose if possible (hose is included in delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry. If mounting on the wall is not possible, you will find suitable chassis in our range on which the dryer can be mounted.   assembly service on request   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If there is no drain, we recommend the appropriate chassis from Roth-Kippe.  Technical data  drying room: up to 35 m² Drying performance: 3.00 - 4.74 kg/h depending on fan speed Consumption per kg of laundry: 0.21 - 0.27 kWh depending on fan speed Energy efficiency: A Tension: 230V / 50Hz Power consumption: during normal operation in "ECO" mode 0.75 kW with heating switched on ("H" models): 1.75 kW Sound pressure level: Fan level 1: 54 dB(A) Fan level 3: 69 dB(A) (Manufacturer's information at 3 m distance) air circulation volume: n/a condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R32 (GWP 675) Dimensions (H/W/D): 77 x 70 x 38.5 cm Weight: 64 kg Operating setting: touchscreen Ambient temperature: 8°C ~ 30°C (ideal: 15°C or warmer) Swiss plug: Yes hose connection: Yes Guarantee: 3 years                                                 Training video for assembly:    

Read more less

The Lübra SecoTec 1700 tumble dryer - from the top ten list - is a high-quality room air tumble dryer and is suitable for drying rooms shared by 2-4 people. Thanks to the new double radial fan, it distributes the 1450m³/h of dry air with good pressure even in larger rooms and is noticeably quieter than dryers with comparable dehumidification performance. Easy operation with the Lübra control • Function switch: here you can choose whether the device should only dry the laundry and then switch off automatically, or whether it should keep the room at a constant target humidity. In this mode, the dryer always runs when the room humidity is higher than the set desired humidity, otherwise the dehumidification and fan pause. • Hygrostat wheel: Rotary switch with which the desired target humidity can be easily regulated. • Start button: If you do not want to change any of the settings, you can start (or stop) the operation by simply pressing the start button. This is an easy-to-understand solution, particularly in drying rooms for several parties. A plexiglass cover is also available on request, which prevents access to the function wheel and hygrostat so that the settings cannot be changed. ambient temperature Technically, Secotec tumble dryers can be used down to 5°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. For optimum drying speed, 15°C and higher are optimal. The declared drying performance was measured at a room temperature of 20°C.  execution - Plug-in dryer, robust sheet steel housing, white powder-coated - Wall mounting rail with anti-noise rubber buffer, required screws/dowels - Hygrostat - reusable filter - Laundry drying program with end-off function (when the laundry is dry, the device switches off completely) and room dehumidification program (the device always works when the room humidity is higher than the set target humidity value).  mounting on the wall As with all tumble dryers, installation is extremely simple: a mounting rail is anchored into the wall using 2 screws, and the device can then be hung up. All necessary mounting material such as screws/anchors and 2m of hose is included in the scope of delivery. Both the support rail and the two buffers in the lower part of the device that support the wall are insulated with rubber to minimize the transmission of vibrations to the wall. Due to the high dehumidification performance, we recommend draining the condensate directly into the sink using the hose if possible (1m of hose is included in the scope of delivery). If you want to use a bucket, please ensure that it has enough capacity (at least 8 liters) to avoid overflowing while drying laundry.   If you wish, we can professionally install the dryer at your home within a radius of 120 km (CHF 210.-), prices for further distances on request. Calculate distance Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. Technical data country of production Switzerland energy efficiency class A1 power consumption 870 watts supply voltage 230 V drying capacity at 15kg 2.93 kg/h consumption 0.30 kWh / kg laundry noise level (our measurement) 65 db(A) at 2.5m distance 68 dB(A) at 1m distance air circulation 1450m³/h Room temperature use from 5 - 30 °C Dimensions (HxWxD) / Weight 740 x 440 x 410 mm Weight 44 kg coolant (CFC-free) R410a guarantee 3 years  

Read more less

A strong model of the current Krüger Secomaten. It is suitable for single-family homes with large amounts of laundry as well as for drying rooms in multiple apartments. It has various functions, which combine the previous separation into AH (endless operation) and E (end-off) models in one device: drying programs drying clothes It is operated at the touch of a button. You can choose between light, medium or high drying levels. The tumble dryer works fully automatically and, similar to the previous models, with what is known as an end-off control, which means that it dehumidifies until the laundry is dry and then switches off automatically. If you want to use the device again, you have to restart it manually. basement dehumidification The dryer is also equipped with a button for keeping the room dry. The device runs whenever the humidity is too high and there is a risk of mold/odors forming in the basement. If the humidity is right, the device stops. timer function It is also possible to operate the device manually for 30, 60 or 90 minutes. After the time has elapsed, the device switches off and manual operation is automatically switched off. execution Compact device with powerful ventilation. Slats for air outlet, which can be adjusted horizontally if required. The clearly laid out control panel is limited to 4 buttons on the front. The support rail and the two spacer buffers in the lower part of the device are insulated with rubber to reduce the transmission of sound to the wall. The mouse-gray color of the housing is individually pleasing. Heating option : This model is also available with a 1350W heater for an additional charge. This switches on automatically at 14°C (or colder) and heats until the room temperature reaches 16°C. This heater is therefore only useful in very cold drying rooms. If the room is 16°C or warmer all year round, the version with heater offers no advantage. Technically, the Secomat tumble dryers can be used down to 10°C. Please note that the drying time for all room air tumble dryers increases significantly the colder the room is. 15°C and higher are optimal for optimum drying speed. The declared drying performance was measured at a room temperature of 20°C. scope of delivery The delivery includes the device with support rail, all necessary mounting material and a drain set. The drain set consists of a water tank, drain hose and suitable hose connection couplings. assembly If you wish, we can professionally install the dryer at your home for CHF 210.-. Important: - Sanitary (drain) or electrical (230V socket) installations are not carried out by us and must be commissioned separately by you through an appropriate craftsman, if one does not already exist. - If your wall has internal insulation, we need to know this when ordering, as installation is more complex. The installation prices quoted refer to direct wall installation, i.e. directly on brick or concrete walls without insulation. Additional costs for installation on insulated walls are charged according to the effort involved. If wall mounting is not possible, we recommend the appropriate Secomat chassis.     Technical data  Krüger article: 388.01 drying room: up to 25 m² Drying performance: 3.17 Kg/h Consumption per kg of laundry: 0.30 kWh Energy efficiency: A1 Tension: 230V / 50Hz Power consumption: max. 989W or 950W (at 20°C/60% RH) Version with heating Secomat 100H: Heating switched on = +1350W Sound pressure level: 69 dB(A) (manufacturer's specification with 15kg of laundry in the room) Examples of dehumidification performance and consumption: at 20°C / 60% RH = 28.0 liters / 24h (power consumption: 950 W) air circulation volume: 1300 m³/h condensate tank: No integrated tank. The water is supplied via a hose connection directly into the drain or into a bucket. Compressor: rotary compressor refrigerant: R407c / 550g Dimensions (H/W/D): 690 x 655 x 395 mm Weight: 47 kg Operating setting: program keys Ambient temperature: 10°C ~ 30°C Swiss plug: Yes hose connection: Yes Guarantee: 3 years

Read more less