With this high-quality laser scanner, you can check surfaces, such as interior walls and facades, for potential mold hazards caused by cold spots. You can quickly and easily measure wall surface temperatures contactlessly using infrared and at the same time automatically determine the dew point temperature value.   The backlit LCD display allows you to clearly and easily read the measured values ​​even in poor lighting conditions. The integrated 20:1 dual laser shows you the measuring spot on the respective measuring object.   To determine the dew point, the device also measures the current room temperature and the humidity of the air. Thanks to its acoustic and visual alarm function based on the traffic light principle and the integrated bar graph indicator, you have quick information, even with larger measuring areas, as to whether the dew point has been reached or fallen below at a measuring point and whether there is a risk of mold due to condensation. Since a long-term increase in relative humidity of around 70% is sufficient for mold to form on material surfaces, the device warns you both acoustically and visually a few degrees before the actual dew point is reached. It is therefore worth checking cold areas of the wall in order to detect condensation at an early stage.     With 20:1 optics, the measuring spot is always in view   Measure the surface temperature of walls, materials and objects without contact, i.e. without touching the object being measured. The device has a dual laser pointer to be able to estimate the exact area of ​​the measurement (measuring spot). This projects two laser points onto the surface to be measured, which precisely mark the diameter of the measuring spot. The temperature value in this area is recorded by an infrared sensor and an average value is determined. The following applies: the smaller the measuring spot, the more accurate the measurement, and the further the measuring device is from the measuring object, the larger the measuring spot diameter. Thanks to its geometric resolution of 20:1, the hand-held measuring device enables you to take accurate measurements even from a distance of several meters.     Detecting the danger of mold   Since the device has an air temperature sensor and a humidity sensor (measurement range from 0% to 100% relative humidity) in addition to the infrared surface temperature measurement, the dew point temperature is automatically calculated from these three values. In addition to the exact values, an acoustic signal and/or the color of the LCD display can indicate whether the measured values ​​are in the critical range.   Green display: everything is OK Orange display: measured values ​​are approaching the critical dew point value Red display: Temperature is dangerously close to the dew point or has already reached or fallen below it, so that condensation can form.   With the increasingly faster beeping sound signal, you can also work by ear if you wish. Especially when measuring large areas on walls, you can use the acoustic and/or optical alarm to quickly scan where critical areas are - without having to pay attention to the exact measured values. In addition, the bar graph indicator shown on the display offers quick orientation using an easy-to-understand bar diagram and shows you schematically on a scale from 0% to 100% how close the measured values ​​have already come to the dew point temperature.     Versatile   Due to the wide temperature measurement range from -50 °C to 260 °C, this measuring device is not only recommended for use as a dew point scanner but also for other applications. The contactless infrared measurement reliably protects you from surfaces that are too hot or too cold.   Whether it's a heating system, hot pipes, tanks, boilers, engine blocks, switch boxes or deep-freeze storage - measure the temperatures without burning your hands or "sticking" to ice-cold surfaces. This device can even be used for preparing baby food if you want to quickly check the correct drinking temperature of the bottle from the outside, for example.     With its compact dimensions, the device weighs just 163 g and can be easily carried in a jacket pocket. A practical pouch for attaching to a belt is also included in the delivery.   The infrared thermometer is operated wirelessly using the included 9 volt block battery. Thanks to the battery status indicator on the LCD display, you can always see the current charge level. The automatic switch-off when not in use saves energy - so you can carry out countless measurements!     Advantages at a glance   • Measurement of surface temperature, air temperature, humidity and dew point temperature with just one device • Dew point alarm indication by display color change, alarm tone and bar graph indicator • Non-contact surface temperature measurement via infrared from -50 °C to 260 °C • Measuring optics 20:1 • Measuring spot diameter display by dual laser pointer • Backlit display • Auto shutdown • Practice-optimized German industrial design – protected design • Optimal price-performance ratio   scope of delivery   • Measuring device • 9V battery • Operating instructions • Protective bag     Technical data   Optical resolution (D:S) 20:1 smallest measuring spot Ø 25.4 mm (distance 508 mm) measuring range sensor -50 to +260 °C Sensor deviation < 20 °C ± 3.5 Deviation sensor at 20 °C 1% ± 1.5 measuring range of integrated temperature sensor 0 to +50 °C dew point temperature -30 to +100 °C dew point deviation ±2.0% humidity measuring range 0 to +100 % RH humidity deviation ±3.5 % (between 20-80 % RH) response time temperature sensor < 150 ms Spectral sensitivity 8 - 14 µm energy supply 1 x 9 V block battery (included) Dimensions (H x W x L) 82 x 58 x 168 mm Weight 163 g Trotec article no. 3,510,003,035 guarantee 2 years

Read more less

A precise measuring device for quick control and monitoring of environmental noise, noise in the workplace and in the private environment. Measures noise sources within a measuring range of 30 to 130 dB(A). Minimum and maximum values ​​can also be displayed and saved.   This easy-to-use sound level meter combines modern electrodynamic sound transducer technology in a compact design. As a sound level meter corresponding to accuracy class 2, the device is ideal for documenting machine and environmental noise or workplace and noise hazard measurements.   The large four-digit measurement display with additional bar graph display is easy to read in any environment thanks to the LCD backlight.   With A and C frequency weighting, fast-slow time weighting and many other practical functions, this measuring device from the MultiMeasure Professional series is the perfect solution for demanding sound level measurements.   Handy format, low weight and button layout optimized for one-handed operation.     Versatile application, for example   • Noise hazard measurements for occupational safety • Environmental protection operations to determine environmental noise • Determination of noise areas for noise reduction programs in companies • Checking and selecting hearing protection devices • Compliance monitoring of noise protection regulations • Control measurements in air conditioning and heating technology     Advantages at a glance   • Corresponds to accuracy class 2 • Frequency evaluation according to characteristic curves A and C • Maximum and minimum value memory • Memory for 50 measured values • Switchable time evaluation (Fast?/?Slow) • Display lighting • BarGraph display • 1/4-inch tripod thread     scope of delivery   • Measuring device • Battery • Wind protection • Carrying case • Operating instructions     Technical data   sensor technology Sound dB(A) + Sound dB(C) sound measuring range 30 - 130 dB(A) sub-measuring ranges 30...80 dB, 50...100 dB, 80...130 dB, 30...130 (auto) dB(A) accuracy Class 2 according to DIN EN 61.672 resolution 0.1 dB(A) response time 0.5 seconds frequency range 31.5 Hz - 8 kHz dynamic range 50 dB data storage 50 measured values power supply 9V block battery operating time > 30 hours Weight 230 g Dimensions (H x W x D) 210 x 55 x 32 mm Vicinity: temperature humidity 0 - 40 °C 10 - 90 % RH (non-condensing) Trotec article no. 3,510,005,010 guarantee 2 years

Read more less

Measure and document climate data. Long-term measurement with up to 32,000 stored values. The device stores up to 32,000 measurement data; you determine the measurement cycle and time. To ensure that the recording remains protected from manipulation, a lockable wall mount is included in the delivery, which protects the device from unwanted access. Since the recording is configured exclusively via PC, it is not possible for unauthorized persons to manipulate the configuration directly on the measuring device.   The data logger can also be evaluated and configured using the free MultiMeasure Studio software (STD). The optional professional version of the software also allows, among other things, export to Excel table format or the creation of automated reports for the corresponding evaluation.     application examples   • Proof of compulsory inspection for craftsmen • Determination of the causes of mold and moisture damage • Logging of climate data in archives and storage rooms     scope of delivery   • Measuring device • Battery • PC analysis software • lockable wall mount • Operating instructions • USB cable     Technical data   measuring range air temperature -40 °C to +70 °C (-40 °F to +158 °F) resolution air temperature 0.1 °C accuracy of air temperature max. ±1 °C measuring range relative humidity 0 % RH to 100 % RH resolution relative humidity 0.1% RH accuracy relative humidity max. 3% RH measured value memory a total of 32,000 measurements 16,000 each for temperature and humidity temperature display in °C and °F Dimensions L x W x H 94 x 50 x 32 mm Weight 91g including batteries functions • Display of maximum value + minimum value • Display of date and time • Alarm function • freely selectable measuring cycle from 1 second to 24 hours • Permanent or ring recording  Trotec article no. 3,510,205,520 guarantee 2 years

Read more less

This electronic moisture indicator measures up to 4 cm deep into solid materials such as brick or concrete walls or even floors. This makes it possible to locate water that has leaked out, for example after a pipe burst. The drying progress of fresh subfloors can also be easily monitored.   Due to the dielectric measuring method, the moisture indication is absolutely non-destructive. No electrodes or probes need to be inserted into the material being measured. The response time is less than a second. At the touch of a button, additional information such as minimum and maximum values ​​are available on the easy-to-read display with backlight. The current measured value can also be saved using the hold function.     functions   • Minimum and maximum value display • Hold function • Illuminated display • Automatic shutdown     Advantages at a glance   • Fast and non-destructive indication of moisture distribution in near-surface areas • Useful pre-test device for CM measurements • Minimum value, maximum value and hold function • Automatic function and battery test • Ready to use • Optimal price-performance ratio • Illuminated display • Automatic shutdown    scope of delivery   • Measuring device • Battery • Operating instructions     Technical data   voltage 9V battery measuring range digits 100 resolution and accuracy 1 digit measuring principle dielectric / capacitive penetration depth 5 - 40 mm (non-destructive) ambient temperature 0 - +50 °C ambient humidity 0 - 80 % RH Dimensions L x W x H 180 x 35 x 45 mm Weight 180g Trotec article no. 3,510,205,031 guarantee 2 years  

Read more less

The compact and handy pocket-sized pH meter is ideal for aquarium and plant lovers, but also for swimming pool owners. It is also suitable for professional applications, such as measuring pH values ​​during quality control in the food and beverage industry or for quick and reliable water control.   Natural ponds have become increasingly popular in recent years. They are usually in a natural balance and do not require the addition of chemical aids. However, regular checking of the pH value can help avoid surprises. Rain or filling with tap water can cause the pH value to shift into an acidic (pH < 7) or alkaline (pH > 7) environment. The tolerance range for fish is between pH 6.5 and 8.5. Ideally, the pH value of the pond water should be around pH 7 (neutral) and remain as stable as possible over time. Maintaining and regularly monitoring the correct pH value is also essential for swimming pools and private pools, especially if they are located outdoors. If the water becomes too acidic or too alkaline, this not only has a negative effect on the people swimming in it (burning eyes, itching). It also affects the formation of algae, the aging of the materials used in the pool (corrosion, decomposition of calcareous materials, porosity, etc.) and the effectiveness of the disinfectants added.   Thanks to the automatic temperature compensation and the use of auto-calibration, the measuring device allows the quick and precise determination of the pH value between pH 0 and pH 14 in the temperature measuring range from 0 to 50 ° C. The device already has a 3-point calibration at the factory, which can be carried out at any time later in just a few steps using the included pH buffer solution set. The result of the test can be found in the easy-to-read two-line display. The determined pH value is displayed (accurate to two decimal places) at the same time as the water temperature. A separate thermometer is therefore not necessary. The practical measuring device has an easily replaceable pH electrode. The electrode and the water temperature sensor are protected from damage by a removable protective cap. A convenient hold function makes it unnecessary to note down the last measured value. An automatic switch-off also reduces energy consumption of the four button batteries included in the delivery.     Advantages at a glance   • Two-line display for simultaneous display of pH value and water temperature • Automatic temperature compensation (ATC) for accurate measurements at different temperatures of the liquids to be tested • Factory 3-point calibration • Auto-calibration for pH 4.01/7.00/10.01 • Easily replaceable pH electrode • Automatic shutdown • Measured value hold function • Optimal price-performance ratio • Includes pH buffer solution set (4.01/7.00/10.01) and protective cap   Note: The device is calibrated at the factory using a high-percentage salt solution. In practice, this often leads to the formation of salt crystals on the diaphragm electrode (fiber bundle). The visible residues are completely normal for pH measuring electrodes of this type. They are harmless to the electrode, can be easily rinsed off with water and therefore do not represent a quality defect.     scope of delivery • Measuring device • Batteries • Operating instructions • pH buffer solution set (4.01/7.00/10.01) and protective cap     Technical data   voltage 4 x flat batteries LR44 display LCD PH value Measuring range: 0 - 14 pH Resolution: 0.01 pH Accuracy ±: 0.03 pH temperature Measuring range: 0 to 50 °C / 32 to 122 °F Accuracy: approx. ± 0.8 °C / ±1.5 °F Resolution: 0.1 °C / 0.1 °F ambient temperature 0°C to +50 °C humidity 10 - 85 % RH Dimensions L x W x H 188 x 38 x 38 mm Weight 83g protection class IP65 guarantee 2 years

Read more less

Its professional features make this robust clamp ammeter a reliable and perfect measuring device for home users as well as for electricians, tradesmen and service technicians. You can use the measuring device to quickly and easily measure alternating voltages in electrical conductors without having to switch them off, or to check direct current networks in cars, for example.  With these compact clamps, you are always on the safe side when measuring alternating voltage of up to 750 volts. You enclose the electrical conductor with the clamp and the measuring device detects whether voltage is present without contact by measuring the electromagnetic field. This 'galvanic isolation' means that you avoid any direct contact between the circuit to be measured, which also makes it possible to carry out tests on running systems.  In addition, the test device allows you to measure currents of up to 1000 A in the direct and alternating current ranges and to determine direct voltages of up to 1000 volts, both of which can be set using the manual or automatic range selection. Because this also allows you to check the direct current network in your car, for example, the pliers are the ideal measuring device for passionate car hobbyists and professionals in the automotive sector.  With one turn to the next measurement  The device has all the usual standard measuring functions such as resistance, duty cycle and frequency measurement, which you can easily select using the practical rotary switch. You can read further information on the LCD display: The bar graph indicator shows you how close you are to an electrical conductor or its electrical field. The diode tester and the continuity test also enable you to reliably check the electrical system of a vehicle, for example.  With the equipment of a real professional  All measurement results are shown on the backlit 1.8 inch LCD display. The clamp ammeter also scores points with features such as the HOLD function, polarity and overload indicators, and a MIN/MAX display. In addition, the battery-saving automatic switch-off and a low battery indicator ensure problem-free use of the device, while the LED light integrated between the two clamp jaws enables safe work even in poor lighting conditions.  Advantages at a glance • 3 5/6 digit LCD display (max. display 9999) • Robust housing • CAT III 1000 V / 750 V • Alternating current measurement up to 1000 A • DC measurement up to 1000 A • AC voltage measurement up to 750 V • DC voltage measurement up to 1000 V • Highest resolution in the milliampere range • Contactless detection of alternating voltage • Resistance measurement • Duty cycle measurement • Frequency measurement • Continuity test and diode test • Polarity indicator • Overload protection • Low battery indicator • Automatic and manual range selection • Measured value hold function • Display lighting • Bar graph indicator • Integrated white light LED for working in poor lighting conditions • Suitable for cable diameters up to 38 mm • Battery-saving automatic shutdown • Includes storage bag • Optimal price-performance ratio     functions   • Measured value hold function • automatic measuring range selection • Display of measuring range exceeded • Measurement of direct current, alternating current, direct voltage, alternating voltage, capacitance, frequency, duty cycle and resistance • Automatic shutdown • backlit display • Diode test • Continuity test • Battery status indicator • integrated LED lamp     scope of delivery   • Measuring device • Batteries • Bag/Holster • Safety measuring leads with test probes • Operating instructions     Technical data   direct current (V/DC) • Measuring range: 6-1000 V • Accuracy±(%)(6V / 60V / 600V): ±(0.8% +5) • Accuracy±(%)(1000V): ±(1.0% +5) • Accuracy±(%): 0.8 %   direct current (A/DC) • Measuring range: 6-1000 A • Accuracy±(%)(60 A): ±(0.3% +10) • Accuracy±(%)(600 A /1000 A): ±(3.0% +6) • Accuracy±(%): 3.0 %   alternating voltage (V/AC) • Measuring range: 6-750 V • Accuracy±(%)(6V): ±(0.8% +5) • Accuracy±(%)(60V / 600V / 750V): ±(1.2% +5) • Accuracy±(%): 1.2 %   alternating current (A/AC) • Measuring range: 60-1000 A • Accuracy±(%)(6V): ±(0.8% +5) • Accuracy±(%)(60V / 600V / 750V): ±(1.2% +5) • Accuracy±(%): 2.5% • Accuracy±(%): ±(2.5% +6)   Resistance (?) • Measuring range: 600-60 M • Accuracy±(%) (600 ? / 6 k? / 60 k? / 600 k?): ±(1.0% +5) • Accuracy±(%) (6 M?): ±(1.5% +5) • Accuracy±(%) (60 M?): ±(3.0% +10) • Accuracy±(%): 3%   frequency (clamp) • Measuring range min.: 40.0 Hz - 99.99 Hz • Measuring range max.: 100.0 Hz - 999.9 Hz • Accuracy±(%): ±(1.0% +5)   frequency (with test cables) • Measuring range: 9,999 Hz - 9,999 MHz • Accuracy±(%)(9.999 Hz / 99.99 Hz / 999.9 Hz / • 9.999 kHz / 99.99 kHz / 999.9 kHz): ±(1.0% +5)   duty cycle • Measuring range: 5- 95 % • Accuracy ±(%): ±(2 % +7)   capacity • Measuring range min.(nF): 40 nF • Measuring range max. (µF): 40 µF • Accuracy ±(%)(40.00 nF / 400.0 nF / 4.000 µF / 40.00 µF / 400.0 µF): ±(5.0 % +5)   • Display: LCD 3 5/6 digits • Conductor diameter max.: 38 mm • Opening pliers diameter: 50 mm • Connection sockets for 4 mm safety plugs: 2 • Measuring circuit category: CAT III (1000 V) • Protection class: IP20 • Conformity: EN 61010-1', 'Pollution degree 2 • Battery type: 3 x 1.5 V, AAA • Ambient temperature (use): 0 °C to 40°C   warranty 2 years   Trotec article number 3.510.205.244  

Read more less

This sensor is an electronic moisture indicator that non-destructively measures the capacitive moisture in solid materials such as walls, floors or ceilings up to a depth of approx. 3-4 cm. The measuring device is ready for use immediately, can be easily connected to the app and allows you to quickly and easily locate moisture distributions close to the surface. Not only is the rapid indication of various near-surface material moisture values ​​possible, this sensor is also particularly suitable for preliminary testing of the readiness of building materials for use in CM measurements.    Advanced evaluation and function thanks to app Compared to non-app-supported moisture measuring devices, users of this device with the free "Multimeasure Mobile" app benefit from numerous additional advantages in terms of flexibility, analysis functions, data control and documentation. Compare different moisture measurements of an object that were taken at different times directly in the app. Or use the measured values ​​in combination for differentiated analyses directly on site. Useful additional features such as the alarm function, the export of moisture measurements to further analysis software and the creation of a report round off the universal application possibilities of the BM31WP and make this measuring device a valuable tool in the field of building diagnostic tasks.  With the MultiMeasure Mobile App, you can not only automatically display the MIN, MAX and average values ​​or mark individual measured values ​​directly in an image, but also create, save and send complex graphical representations in the form of a photo-linked moisture matrix. The grid to be measured can be backed up with a real image and later output as an overlaid graphic with the moisture matrix for documentation purposes – for example for your measurement report, which you can generate and send directly on site from the app.  What is an AppSensor?  Trotec appSensors are compact precision measuring devices with high-quality sensors that are designed to save energy and space and do not have any evaluation electronics or display units, as the operation and data evaluation of the devices are carried out almost entirely via the connected smartphone. In combination with the free "MultiMeasure Mobile" app, this measuring device concept offers many convincing advantages.     app "Multimeasure Mobile" "MultiMeasure Mobile" offers you a variety of advantages: • Auto-detection for appSensors • Parallel operation of several appSensors • Fast and intuitive navigation • Measured value display numerically or as diagram / matrix • Integrated report function for on-site documentation • Organizer function for measurement data and documents • Customer management already integrated • Various analysis options directly in the app • Photo-linked measurement value storage • Matrix measurements, also photo-linked • Complete data synchronization to MultiMeasure Professional via Cloud   Your mobile device becomes a multifunctional measurement data manager. All appSensors are automatically recognized and can be connected to the app and read via Bluetooth. Operation is just as simple and intuitive as installation.    Advantages at a glance • Fast and non-destructive indication of moisture distribution in near-surface areas • Useful pre-test device for CM measurements • Professional sensors for precise measurement results • Easy app connection via Bluetooth with optical connection confirmation via LED on the device • Wireless measuring device control and data display via app • Easy measurement data acquisition even at remote locations, as the values ​​do not have to be read directly on the measuring device • Additional determination and display of minimum value, maximum value or average value • Measurement data storage, logging and alarm function • Hand strap for safe handling included • Automatic shutdown   Trotec appSensors contain professional sensors for precise measurement results; they were developed for exactly this purpose. For professional measurements, use the clever combination of appSensor and MultiMeasure Mobile – the free app for iOS and Android.     scope of delivery   • Measuring device • Batteries • Hand strap • Operating instructions     Technical data   measuring range 0 - 100 digits resolution 0.1 digit measuring principle dielectric / capacitive ambient temperature 0 °C to 50 °C ambient humidity 10 - 90% RH (storage: max. 80% RH) Bluetooth 4.0 (BLE), max. 10 m transmission range in open area Dimensions (L x W x H) 160 x 36 x 22 mm Weight 93 g Trotec article no. 3,510,206,031 guarantee 2 years      

Read more less

The battery-operated 360° laser, which can be used anywhere, uses the all-round projection of a horizontal laser line at the touch of a button to make it easier to attach or mark wallpaper borders, wall tiles, paint edges, wall cabinets or drill precisely placed dowel holes at a uniform height. And all this on all four walls at the same time.   If required, it also projects a vertical laser line onto the opposite wall, for example to align pictures and shelves on this right-angled laser cross or to lay tiles in a precise grid. The projection of an oblique marking line at a freely adjustable angle of inclination is also possible in no time at all. This makes even the otherwise tricky installation of a stair railing installed parallel to the steps child's play.   The combination bracket with universal clamp and suction cup included in the delivery allows a variety of attachment options to objects and surfaces such as glass, panels, a shelf or a ladder. This means that the laser can be easily secured anywhere and can be aligned and tilted exactly as you need it for your work using the adjustable joint on the combination bracket. The high-quality housing of the 360° laser is made of painted aluminum and is therefore ideally suited for the rugged everyday use of the practice.   The integrated laser is self-leveling and compensates for uneven floors up to 3° fully automatically. Self-alignment only takes a few seconds and takes place immediately after the device is switched on. If self-leveling is not possible due to large unevenness or dirt, the laser signals this with a red LED and flashing laser lines.   Three projection modes for almost all alignment work and the multifunctional combination mount make the compact laser, which weighs just 280g, an indispensable precision tool for handicrafts and DIY enthusiasts. With the ¼-inch thread in the base of the device, the device can also be attached to standard tripods, including our universal tripod, which you can order as an accessory.   The integrated lithium-ion battery of the latest generation ensures long-lasting performance and maximum operating times. Even in daily use with frequent partial discharges, the Li-ion battery guarantees a long service life without the memory effect known from conventional NiCd batteries.     Advantages at a glance   • 3 projection modes: 360° horizontal operation, cross line operation, 90° vertical operation • Projects bright laser lines up to 10 m away • Self-leveling rotary laser – always automatically aligned straight • High accuracy of only ± 0.8 mm/m (at 0°) • Ideal for quick and straight alignment of drill holes, pictures, panels, wallpaper strips, wall cabinets, shelves, etc. • Visual warning when outside the auto-leveling range • Includes multifunctional combination mount with universal clamp plus suction cup • State-of-the-art laser technology with ultra-easy handling • Extremely light and ultra-compact • Thanks to battery operation, it can be used anywhere at any time • Durable Li-Ion battery with long service life for maximum operating times • Laser locking function for projecting even diagonal lines • Operating switch with transport position for secure position fixation of the laser when changing location • Integrated ¼-inch tripod thread • Robust aluminum housing • Fast charging via included micro USB cable • Telescopic tripod available as optional accessory scope of delivery   • Measuring device • multifunctional support arm • Micro-USB cable • Charger (USB 5V, 1A) • Quick start guide     product video   Technical data  voltage 220 - 240 V/50 Hz Auto-Leveling area ±3 ° Accuracy - Laser ±0.8 mm/m (at 0 °) Accuracy - Laser ±1 mm/m (at ?3 °) reach 10 m laser class 2 laser power < 1 mW wavelength 650 nm Dimensions H x W x D 115x 60 x 60 mm Weight 280g protection class IP40 display status LEDs (red/green) Housing aluminum power supply 1 x 3.7 V Li-Ion battery internal (included) ambient temperature 0 °C to +40°C Gimbal auto-leveling Yes Projection of cross and single lines yes (360° horizontal, 90° vertical) Laser locking function (transport protection) Yes tripod thread yes, 1/4-inch tripod Multifunctional holder arm (included) Trotec article no. 3,510,205,152 guarantee 2 years

Read more less

The advantage of the flat electrodes (1 mm flat) is that there is no need to drill holes in the surface and the electrodes can be inserted through the edge strip or other joints after removing the base. Comparable to the flat electrode pair M 6-Bi 200. • Insulated shaft to exclude surface moisture. • The electrode length is 200 mm. • Compatible with Gann MK8 measuring cables and UNI measuring devices Scope of delivery: 1 pair (= 2 electrodes as per photo)

Read more less

As a thermal anemometer, this handheld measuring device impresses with its high measurement sensitivity and is particularly suitable for the precise determination of even low flow velocities. It is ready for use immediately, can be easily connected to the app and displays all measured values ​​on the mobile device.   Thanks to the clever combination of appSensor and the associated, free app Multimeasure Mobile, users benefit in practice from numerous advantages in terms of flexibility, analysis functions, data control and documentation.   Compare the data you have collected directly on your mobile device or use the measured values ​​in combination for differentiated analyses on site. The probe design, which can be continuously adjusted in length, and numerous useful features enable universal use for many measuring tasks.   The logging function for long-term measurements, the diagram representation of your measurement data or its export to further analysis software as well as the option to create a report are helpful. From performance monitoring of household appliances to air conditioning and ventilation systems to cooling fans in the IT sector, this measuring device is an ideal companion for flow measurements, even in hard-to-reach places.     app sensor Trotec app sensors are compact precision measuring devices. They have high-quality, energy- and space-saving sensors. The data is displayed, operated and evaluated via the connected smartphone. In combination with the free "MultiMeasure Mobile" app, this measuring device concept offers many convincing advantages.     Advantages at a glance   • Fast and easy measurement of air velocity, air temperature and air volume flow (CMM) • Extendable, 375 mm long telescopic probe • High-quality sensors and numerous measuring functions • Professional sensors for precise measurement results • Additional determination and display of minimum value, maximum value or average value • Measurement data storage, logging and alarm function • Intelligent combination of appSensor and the MultiMeasure Mobile app • Easy app connection and control via Bluetooth with optical connection confirmation via LED on the device • Easy measurement data acquisition even at remote locations, as the values ​​do not have to be read directly on the measuring device • Automatic shutdown • Hand strap for safe handling included     "MultiMeasure Mobile" – Free app for iOS and Android   To operate this appSensor on your smartphone, you need MultiMeasure Mobile – a free app for controlling, evaluating and displaying measurement data from all Trotec appSensors connected to your mobile device.   MultiMeasure Mobile offers you a variety of benefits: • Auto-detection for appSensors • Parallel operation of several appSensors • Fast and intuitive navigation • Measured value display numerically or as a diagram?/?Matrix • Integrated report function for on-site documentation • Organizer function for measurement data and documents • Customer management already integrated • Various analysis options directly in the app • Photo-linked measurement value storage • Matrix measurements, also photo-linked • Complete data synchronization to MultiMeasure Professional via Cloud   All app sensors are automatically recognized by "MultiMeasure Mobile" and can be connected to the app and read via Bluetooth. Operation is just as simple and intuitive as installation. Simply download MultiMeasure Mobile to your mobile device for free.         Technical data   flow velocity measuring range             0 - 30 m/s (resolution 0.01) 0 - 67 mph (resolution 0.01) 0 - 108 km/h (resolution 0.01) 0 - 58 kn (resolution 0.01) 0 - 5900 ft/min (resolution 1.0)   temperature measuring range     accuracy       -20 °C - +60 °C (resolution 0.1) -4 °F - +140 °F (resolution 0.1)   ±0.8 °C (-20 °C - 0 °C) ±0.5 °C (0 - +60 °C)   moisture measuring range   accuracy       10 - 90 % RH (resolution 0.1)   ±3.5 % RH (20 % - 80 % RH) ±5% RH (0% - 20% and 80% - 100% RH)   Bluetooth 4.0 BLE, 10 m range in open area energy supply 3 x 1.5V, AAA batteries Dimensions (L x W x H) device 320 x 36 x 22 mm Telescopic probe extendable approx. 235 mm Weight 122 g Trotec article no. 3,510,206,043 guarantee 2 years

Read more less

The advantage of the flat electrodes (1 mm flat) is that there is no need to drill holes in the surface and the electrodes can be inserted through the edge strip or other joints after removing the base. Comparable to the flat electrode pair M 6-Bi 300. • Insulated shaft to exclude surface moisture. • The electrode length is 300 mm. • Compatible with Gann MK8 measuring cables and UNI measuring devices Scope of delivery: 1 pair (= 2 electrodes as per photo)

Read more less

This data logger measures the CO? air quality in rooms such as offices, classrooms or even in your own home. It has a large data memory for 50,000 measured values ​​for long-term recording of carbon dioxide concentrations, air temperature and humidity values ​​in freely definable measuring intervals from 1 second to 12 hours. It uses a CO? traffic light to show how the air quality is changing.   The recorded data can be easily transferred to the connected PC via a fast USB connection and then evaluated and logged using the analysis software included in the delivery. Thanks to the integrated Li-Ion battery, the CO? data logger can be used in mobile applications as well as in stationary tabletop use.   The simultaneous recording of humidity and temperature values ​​plus CO2 concentrations also provides property managers or landlords with optimal options for monitoring ventilation behavior.     Automatic Baseline Calibration   The CO? fresh air value expected today is around 400 ppm (0.04%vol). This is assumed by the device as the lowest limit (baseline). A special algorithm then permanently monitors the lowest CO? measured value determined by the sensor over several days. This takes place over a preconfigured time interval and slowly corrects any long-term drift detected compared to the expected fresh air value of 400 ppm (or 0.04%vol) CO?.   In normal indoor applications, the carbon dioxide level drops to almost the level of the outside air at some point over the course of a week. By recording the values ​​over a period of 8 days and then comparing the lowest value with the 400 ppm point, the measuring device recognizes whether it needs to adjust the zero point or not. This happens completely automatically. The algorithm thus takes advantage of the fact that the CO2 level in buildings/rooms regularly stabilizes at a minimum for a certain period of time when they are not occupied. In rooms that are permanently occupied or in which there is a constantly increased CO2 concentration (e.g. greenhouses), this principle of automatic adjustment does not work.     Advantages at a glance   • Accurate and long-term stable NDIR measurement of carbon dioxide concentrations in room air • Simultaneous display of CO? values, room temperature, humidity, date and time • Minimum and maximum value function for CO?, air temperature and humidity • Carbon dioxide alarm function with warning tone for freely definable limit values • Additional symbolic CO? indicator display comparable to a CO? traffic light • Large backlit display with easy-to-read measurement value display • Autonomous long-term logging of carbon dioxide concentration, room temperature and humidity • Memory for 50,000 measured values • Freely definable storage interval from 1 second to 12 hours • USB interface for measurement data transfer • For tabletop installation and mobile use • PC analysis software     scope of delivery • Measuring device • Battery(s) • Power supply • USB connection cable • PC software (download) • Operating instructions     Technical data   measuring range CO2 0 to 9999 ppm accuracy ±75 ppm / ±5 % resolution 1 ppm measuring range air temperature -5 °C to +50 °C resolution 0.1 °C accuracy ±1 °C humidity measuring range 0.01 % RH to 99.9 % RH resolution 0.1% RH accuracy ±5 % RH Advertisement LCD power supply 1 x 3.7 V Li-Ion battery or 230 V power supply sampling + storage interval > 1 s interface USB Weight 245 g Dimensions (L x W x H) 90 x 110 x 98 mm Trotec article no. 3,510,205,015 guarantee 2 years

Read more less

The practical telescopic probe makes this precision anemometer from the MultiMeasure Professional series a versatile measuring instrument for determining flow, temperature and volume flow.   For measurements in channels or at remote locations, the probe can be continuously extended up to a usable length of one meter. The combination of a robust hot wire sensor and highly developed microprocessor technology for signal processing guarantees fast and precise measurement results for every requirement, which are clearly displayed on the illuminated dual display of the easy-to-read LC display even in poorly lit environments.     application examples     • Testing of heating systems, ventilation ducts or air conditioning systems • Adjustment of the air flow when using multiple devices • Commissioning • Maintenance tasks • Measurement of air velocity and temperature at air outlets and ventilation slots • Certification of critical environments • Channel measurements • Leak tests on windows or doors     Advantages at a glance   • Measurement of air velocity (in m/s, mph, km/h, kn, ft/min) and air volume flow (m³/min, ft³/min) • Slim telescopic probe - continuously extendable up to 1 m in length - enables measurements even in hard-to-reach places • Large, easy-to-read LCD with backlight and dual measurement display • Point-by-point and temporal averaging • Minimum, maximum and hold function • Delivery including calibration certificate      Optional   First, read the data stored in the device, such as images, Excel tables or graphics, using the software included in the delivery. Now transfer the results using copy and paste into one of the ready-made report templates in the MultiMeasure Studio PRO software (download MultiMeasure Studio STD), which you can use to create professional measurement reports easily and in no time at all. The text modules (currently only available in the German version) and sample reports included can be edited as required and can also be put together at any time to create new templates defined by the user.     scope of delivery   • Measuring device • evaluation software • Operating instructions   Technical data   air flow measurement measuring range accuracy resolution measuring principle   measuring air volume measuring range   measuring air temperature measuring range accuracy resolution   0.1 to 25 m/s ± 5% of the measured value + 1 measuring unit 0.01 m/s hot wire     0.001 - 999,000 m³/min or ft³/min     0 °C to +50 °C ± 1 °C 0.1 °C   display LCD interfaces USB energy supply 9V block battery ambient temperature 0 °C to +50 °C Dimensions L x W x H 210 x 75 x 50 mm Weight 280 g tripod thread yes, 1/4 inch Automatic shutdown Yes Trotec article no. 3,510,205,042 guarantee 2 years  

Read more less

What medicine calls a “minimally invasive procedure” can also be carried out effectively and purposefully in everyday life: the “examination” with the help of an endoscope. The small camera of the videoscope is inserted into the interior of hard-to-reach cavities and the footage can be seen live and in color on the 3-inch LCD display.   This method makes it very easy to search technical areas, cable ducts, pipes or engines for possible damage or to carry out regular maintenance checks - even when the probe is under water. The advantage is obvious: technical devices do not have to be laboriously dismantled, drywalls do not have to be pried open, water circulation systems do not have to be emptied or cable and pipe ducts do not have to be exposed. Even in the event of a pest infestation, this small camera can be used to quickly check where insects and rodents are finding shelter.     For professional and private use   Ideal for caretakers, technicians or home users - when it comes to a reliable and fast endoscopic visual inspection. Whether indirect optical inspection of hidden machine parts or for insights into cavities that are only accessible through small openings - the narrow and semi-flexible gooseneck probe with mini camera has a diameter of just 5.5 mm and is therefore ideal for in-between car inspections or an insightful look into narrow, hidden places such as gaps, drains, pipes or cable ducts.   The pre-bendable 95 cm long gooseneck probe can be inserted into small openings and the four-stage dimmable light from 6 LEDs ideally illuminates the surroundings for high-quality inspection images - even under water. The LCD color display delivers razor-sharp photos and videos with a high resolution of 1280 x 720 pixels and a 3x zoom is available for magnifying the view. The practical image rotation function by 180° simplifies the display in the event that the image is displayed upside down due to the position of the probe.     With 3 different attachments suitable for all purposes   If required, the tip of the gooseneck probe can also be equipped with a 45° mirror, hook or magnet attachment, thus expanding the range of functions. The 45° mirror attachment included in the scope of delivery enables, for example, a "look around the corner" or a closer look at the object from different perspectives. With the magnet or hook attachment, you can move objects out of the way or take them out. Thanks to the wireless operation, the device is extremely flexible and user-friendly. The display is equipped with a date and time display for precise temporal documentation. You will receive a complete set including all the necessary utensils for immediate use in a practical carrying case. Please note: To save photos and videos, you also need a micro SD card with up to 32 GB of storage space.     Compact and fully equipped all-rounder   45° mirror attachment In order to be able to carry out a thorough inspection from all sides and from different perspectives, a 45° mirror attachment is included in the complete set. This even allows you to look around corners.   hook attachment Once you have located and located the missing object or a foreign body using the probe, you can easily recover or remove it using the hook attachment. Many a piece of jewelry that was thought to be lost has been found again in this way.   magnetic attachment Without the hassle of moving furniture, screws, nuts, coins and other metal parts containing iron, nickel or cobalt can be easily found or removed from under heavy cupboards and sofas, or earrings and rings can be quickly and safely located in the drain. The recovery is easy using the practical magnet attachment on the camera.   Brightness control brings light into the darkness Of course, there are no daylight conditions in hollow spaces, cable ducts and covered areas. In order to have a perfect view here too, the camera has its own light sources that illuminate the respective environment appropriately and provide brilliant photo views. It is equipped with a camera light and an equipment light.   camera light on the probe head The camera light, which can be adjusted to 4 brightness levels, has 6 integrated LEDs and ensures perfectly illuminated inspection photos and videos.   device light There is a device light on the back of the handset that can be used to illuminate objects for a better view. Alternatively, this light source can also be used as a flashlight.   photo and video functions Brilliant image and photo playback with a maximum camera resolution of 1280 x 720 pixels. For a detailed view, you can "freeze" an image sequence during the ongoing video transmission and examine it more closely as a still image. Using the 3x zoom, image sections can be enlarged 1.0x, 1.5x and 2.0x. If a micro SD card is inserted in the device, all recordings can be saved as photos or videos. Thanks to the practical flip function, the image can be rotated 180°, so that you get a perfect view in almost any working position.     For universal applications   Find faster instead of searching for a long time With the videoscope, you can easily inspect places that would otherwise be inaccessible. This means that small parts that have accidentally fallen down, such as screws in the engine compartment or on hard-to-reach machine parts, can be found more quickly and effortlessly fished out using the easy-to-install hook or magnet attachment.   Waterproof immersion At the tip of the gooseneck probe is a color image camera head with adjustable lighting that is dust and waterproof to IP67 protection class. This means you can immerse the probe in water and quickly check whether, for example, unwanted objects are blocking the patio drain.   Check machine condition Compact machines or devices with a solid housing in particular cannot be opened easily. To be able to take a look inside the device, simply insert the 5.5 mm wide gooseneck probe into a suitable opening and use the display to get a comfortable all-round view of the inspection area.   The quick car inspection Even without dismantling the entire engine block, you want to know where the leak is, where water is dripping onto the floor, which cable the marten has ripped out, or where there is an obvious cable defect. Simply switch on the device, insert the probe, and check the situation on the display.   Finding Uninvited Roommates Insects and mice like to live in the furthest corners of the attic or basement. Other vermin such as ants also like to spread out in partition walls and are just as harmful. Now you can easily search for the pests and their nests or remains without having to do major clearing work or even removing wall, ceiling or floor coverings.     Advantages at a glance   • 3 inch digital LCD color display • 95 cm long, semi-flexible and pre-bendable gooseneck probe (Ø 5.5 mm) • Waterproof to IP67 protection class (gooseneck probe and camera head) for underwater use • Includes 3-piece accessory set with 45° mirror, hook and magnet attachment • Still image, photo and video mode • High-quality camera with a resolution of 1280 x 720 px • Taking photos and videos - can also be saved with a Micro SD card of up to 32 GB • 6-fold LED light on the camera head with 4 brightness levels • LED light in the housing (flashlight function) • Compact probe winding • Flip function for 180° image rotation • 3x zoom • Depth of field 1 cm to 30 cm, field of view 65° • Date and time display • Robust construction • Wireless battery operation for mobile, mains-independent use • Battery status indicator • Includes 4 x alkaline LR6 AA batteries, 1.5 V • Protective carrying case • Simple intuitive operation    scope of delivery   • Measuring device • Mirror adapter • Magnetic adapter • Hook adapter • Batteries • Carrying case • Operating instructions     Technical data   display Color display, 3 inch LCD (640 x 480 pixels) memory SD card 32 GB max. (optional) file formats JPG (photo) + AVI (video) Dimensions H x W x D 162 x 85 x 35 mm Weight 385g protection class IP67 power supply 4 x AA batteries (included) ambient temperature -10 °C to +60°C Trotec article no. 3,510,009,122 guarantee 2 years

Read more less

Even at low concentrations, ozone in the ambient air has a high potential for damage. Compliance with safe ozone limits is therefore very important to protect the health of humans and animals. With this measuring device you have the optimal test instrument for quick and precise control or long-term recording of ozone concentrations in the ambient air.   Ozone is a practically colorless gas and is produced naturally or technically. It consists of an unstable compound of 3 "O" atoms (=O3), which decomposes into oxygen (O2) after a relatively short time. In the O3 compound it is strongly oxidizing and disinfecting. It kills germs, bacteria, viruses and odors with 3000 times the power of chlorine treatment. It is therefore used in various areas to disinfect air and surfaces. However, before the treated rooms can be opened to people and animals again, it is important that the ozone value is within the permissible range. This measuring device is used for this purpose.   The device is characterized by very low cross-sensitivity to other gases or VOCs and impresses with fast measurement results with high accuracy even at the smallest ozone concentrations.   Many integrated functions such as the ozone zero adjustment, the reference value measurement option for short-term limit value and time-weighted average value or the switchable value display from ppm to µg/m³ make the fast-reacting measuring device an indispensable aid for the precise determination of ozone pollution. In addition, it is an environmental measuring unit with which air temperature and humidity can also be determined or dew point and wet bulb temperature can be calculated. The dual display of this measuring device always shows you two measured values ​​at the same time at a glance. The device can also be attached to a tripod for long-term measurements. It also has a mini USB port and a 9 V hollow plug socket, so that permanent mains operation is possible via these interfaces as an alternative to using batteries. Last but not least, a power bank can also be connected to the mini USB port for mobile power supply if required.   Advantages at a glance • Fast and precise detection of even very low ozone concentrations • Ozone measurement value display in ppm or µg/m³ • Fast response time • Low cross-sensitivity to VOCs • Ozone zero adjustment function • Ozone reference value measurement (STEL/TWA) • Atmospheric pressure offset for high-precision standard cubic meter measurements • Measurement of air temperature and humidity • Calculation of dew point and wet bulb temperature • Offset setting for air temperature and humidity • Data hold, min, max and alarm function • Display lighting • ¼-inch thread for tripod mount • In addition to battery operation, mains operation is also possible for continuous measurements • Energy-saving auto-shutdown • Calibration certificate included     Diverse application possibilities   • Workplace measurements in industry and commerce • Environmental analyses • Checking production environments • Limit value controls after use of ozone generators for odor neutralization or disinfection, for example in the hotel industry, drinking water treatment and fire and water damage restoration     scope of delivery   • Measuring device • Batteries • Operating instructions • Calibration certificate • Carrying case     Technical data Ozone (O3) measured value ppm min. 0, max. 1 ppm deviation <0.1ppm: ±0.02ppm, or ±10% of the current measured value Ozone (O3) µg/m³ min. o, max. 1,996 (at 20°C and 1,013 hPa) deviation <200 µg/m³: ±40 µg/m³, or ±10% of the current measured value temperature 0 to +50°C resolution 0.1 °C deviation ± 0.6 °C moisture 0 to 99.9 % RH resolution 0.1% RH Deviation 0% - 10% Deviation 10.1% - 70% Deviation 70.1% - 99.9% 5% 3% 5% battery (internal) 4 x AAA 1.5V (included) Weight 185 g Dimensions (L x W x H) 290 x 110 x 80 Trotec article no. 3,510,006,110 guarantee 2 years

Read more less